 | | Re: Beginners Quest.
|
|
Well, I almost sure that you have to use the A1, the other chips have a different configuration, like they can have an eeprom. (23 years ago, 13-Jun-01, to lugnet.robotics.handyboard)
|
| |
| | Beginners Quest.
|
|
Hi all there, Plz can somebody tell me if I can use MC68HC11E1, E0 or F1 chip instead of HC11A1. I've just looked into archives and found nothing about that. Thx for help. (23 years ago, 12-Jun-01, to lugnet.robotics.handyboard)
|
| |
| | Re: two Qs
|
|
Hi, (...) (int (...) Yes. You still can use motor library to control the speed if using separate motor supply. (...) You can check the following link: (URL) Regards, Patrick Hui (URL) (23 years ago, 11-Jun-01, to lugnet.robotics.handyboard)
|
| |
| | Re: two Qs
|
|
Q.1) Yes. Q.2) I don't know this sensor. Bye. (23 years ago, 11-Jun-01, to lugnet.robotics.handyboard)
|
| |
| | two Qs
|
|
Hello... I'd like to ask two questions regarding my H.B; Q.1) If I cut the motors power-trace on the H.B to connect an external 24 volt dc power supply. Would I still be able to control the speed and direction of the motors by software using the (...) (23 years ago, 11-Jun-01, to lugnet.robotics.handyboard)
|
| |
| | Re: download .s19 problem
|
|
(...) Ok, i searched a bit in the net and found out that S0 is a header record (with no usefull information, or!?). So it seems to me that dl from Randy Sargent doesn´t work with *.s19 files with a S0 header (or does it work for anyone else?). So (...) (23 years ago, 7-Jun-01, to lugnet.robotics.handyboard)
|
| |
| | Re: download .s19 problem
|
|
(...) Heyho! Hmmm, are you sure? But why does it work then when i change S0 to S1? I don´t change the memory map with this. But can somebody tell me a site, where the different S Types are explained? I know S1 (a normal dataset) and S9 (the last (...) (23 years ago, 7-Jun-01, to lugnet.robotics.handyboard)
|
| |
| | Polaroid 6500 Works Only When Phonecord is Connected
|
|
Hello everyone, I think my post subject is self-explanatory, but let me broaden a little more. I've connected the P6500 to the expansion board which uses and external 9V battery connected to J13 as it's power source. Now, I can only get valid (...) (23 years ago, 5-Jun-01, to lugnet.robotics.handyboard)
|
| |
| | Troubles with Hamamatsu P3062-01 IR photo reflector / P5587
|
|
Hi, Can anyone help me. I’m trying to use Hamamatsu P3062-01 IR photo reflector) as a shaft encoder ( which is compatible to the P5587) with my Handy Board. The P3062-01 is connected to a digital input. But it doesn’t work: the digital input doesn’t (...) (23 years ago, 4-Jun-01, to lugnet.robotics.handyboard)
|
| |
| | Handy Board web site ISP switch
|
|
Hi all, I'm switching to a new ISP to host the Handy Board web site. During the next few days, the URL might not resolve properly. If you have trouble loading handyboard.com, you can use (URL) . This works now. Hopefully the switch-over will be (...) (23 years ago, 31-May-01, to lugnet.robotics.handyboard)
|
