 | | Re: Twitchy servos
|
|
(...) I'm using a 80C32 board and control two servos by generating a PWM signal with a timer interrupt. It frequently happens that the servos twitch. In my experience the period of 50 ms of the PWM signal was too great. The problem disappeared when (...) (28 years ago, 21-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | MEMORY FAULT
|
|
When I turn my HB on I get the message "MEMORY FAULT" what does it mean and how do I fix it? Thanks, Peter Eacmen (28 years ago, 21-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | RE: dual servo update
|
|
Two things to note in the servo investigation: (...) This supplies a reserve of current to the servos, and that allows them to seek to their desired position faster. (...) Two servos, when moving, can pull two AMPS of current. Thats 2000mA. Two (...) (28 years ago, 21-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | Stepper Motors driving [DAT]
|
|
Hi - I am new to this list but the archive indicates some interest in driving stepper motors on the HB so here is my little bit: If we have a typical four coil, unipolar stepper such as those found in disk drives, they will have connections (...) (28 years ago, 21-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | Re: IR Demodulator
|
|
(...) I'll post this again: 4 sharp GP1U58Y: 40KHz IR Receivers for $12 From page (URL) them at mek-orders@orlandone...igital.net These are compatible with the IS1U60 as far as i know. I ordered 4 of them and they were shipped to me in the (...) (28 years ago, 21-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | Re: dual servo update
|
|
Hi, I spent a bit of time a couple of months ago re-arranging a lot of the Pcode (we all get our kicks different ways!). At that time, I concluded that the printf routine (or more specifically the despooling function of the buffered characters going (...) (28 years ago, 21-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | Re: addendum
|
|
Ahah. due to the arcane way printing to the lcd screen is implemented, all interrupts must be turned off each time a character is written to the lcd. apparently this conflicts with the servo routines. i'll look into it and see if there is a (...) (28 years ago, 21-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | addendum
|
|
Hello again, I forgot to include the most interesting part of my findings. Removing printfs from my routines (which I did independently from all other fixes) markedly improved performance of the servos. This is actually one cause of trouble which I (...) (28 years ago, 21-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | Re: IR Demodulator
|
|
I too am interested in getting the Sharp IS1U60 but have not been able to locate it. Scott sherman@plains.nodak.edu (...) (28 years ago, 21-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | dual servo update
|
|
Hi, For any interested dual servo users the following is what I have been able to find regarding the twitching. Wiring a 1000microf electrolytic across the 6V within inches of each servo seems to work. However, a much more important fix has been (...) (28 years ago, 21-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | IR Demodulator
|
|
Hello Everyone, I have had absolutely no luck in getting a IR Demodulator for my HB. I have tried every source given on this sight and even more. Can anyone help me to locate this part? Sharp (IS1U60) Having No Luck! Bill Rose (28 years ago, 21-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | Re: mosfet H-bridge
|
|
I would also be interested in plans for such an H-Bridge. I have two 12Vdc motors than take 3.5 Amps at full load (actually gearhead motors so I get lots of torque @50 RPM) but they have surges us to 12 - 14 Amps at start-up and if they get stalled. (...) (28 years ago, 20-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | RE: mosfet H-bridge [DAT]
|
|
Sure, I've built several. The only "trick" to MOSFET bridges is that if you use all N-channel FETs you need a charge pump on the upper FETS. (look out for typos, this was done 'off the cuff' so to speak.) Chuck's Simple MOSFET Tutorial ---...--- (...) (28 years ago, 20-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | mosfet H-bridge
|
|
Hello, does anyone know how to build a mosfet hbrige and, if so, could they pass that on to me? It is my understanding that the mosfet hbridge does not heat up near as much as the transistor hbridge nor does it have any loss of voltage or current (...) (28 years ago, 20-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Sensors
|
|
(...) Voltage. (...) Yes. (28 years ago, 20-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | More Sensors
|
|
What is the smallest difference between voltages that the HB can differentiate between at its analogue inputs.I am very grateful for the information which has already been supplied in reponse to my queries and have found it useful though not (...) (28 years ago, 19-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Robot Soccer Teams
|
|
Perhaps someone can post it on their HomePage or something so that we all can read it. :) (...) (28 years ago, 19-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | Twitchy servos
|
|
Hi. I also have the problem of twitchy servos, but I am currently only using one of them. The servo is used in steering and it constantly twitches. Although, when I have nothing else hooked up to the board and have only the servo running, no twitch. (...) (28 years ago, 18-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | Re: Ranging
|
|
(...) The Polaroid sensor (50-60 KHz, 1.5-30 feet but maybe more from the air?) is $49 (minumum two) direct from Polaroid. They are in the FAQ or I can look up the ordering stuff if you are interested. There is plenty of documentation for using the (...) (28 years ago, 18-Jan-97, to lugnet.robotics.handyboard)
|
| |
| | Robot Soccer Teams
|
|
I just read in Nuts & Volts about your triumph!! What an impressive feat! Doesn't it get boring having your robots beat the competition 15 to zip? Just kidding.. I can imagine the excitement you all must have felt to see your creation take off seem (...) (28 years ago, 18-Jan-97, to lugnet.robotics.handyboard)
|
