|
 | | Re: Struggling with encoder wheel
|
| As I am not so purist, I think that an angle sensor based on a small potentiometer (There's a description on Michael Gaspari's site) would be the simplest solution... But your absolute encoder is a challenge in itself! What about using two (...) (26 years ago, 13-Apr-01, to lugnet.robotics)
| |
|   sensor, sensors (score: 0.565) |
|
 | | Re: Struggling with encoder wheel
|
| hi Chris, (...) That's in fact a good principle. Isn't it possible to improve the dynamic range of the light-sensor by taping the red LED, I read that somewhere but I don't know where. Why not use a continuous grayscale, with pure with and black (...) (26 years ago, 12-Apr-01, to lugnet.robotics)
| |
|   sensor, sensors (score: 0.565) |
|
 | | Re: Robolab software which kit
|
| In article <5784415.post@talk.nabble.com>, Tom Stiles <lego- robotics@crynwr.com> wrote (...) I think it is only sold separately. It is distributed by Lego Education for schools and colleges, alongside variously themed kits that include an RCX and (...) (20 years ago, 14-Aug-06, to lugnet.robotics)
| |
|   sensors (score: 0.564) |
|
 | | Racing Line Follower
|
| Hello I've built a line follower which is quite fast (approx 4 secs per lap on the testpad). It consists of two motors, each powering a 2/3 geared large wheel. Two light sensors are attached to the front pivot wheel. The distance between the sensors (...) (26 years ago, 2-Apr-01, to lugnet.robotics)
| |
|   sensor, sensors (score: 0.564) |
|
| |
|   sensors (score: 0.564) |
|
| |
|   sensors (score: 0.564) |
|
 | | calculating sensor resistance (Ohm's Law)
|
| I've been helping my little sister with her RCX-intensive science project, but we just finished all the calculations and her results seem screwy. Does anyone who understands RCX internals and/or Ohm's Law have some time to look this over and make (...) (26 years ago, 6-Apr-01, to lugnet.robotics)
| |
|   sensor, sensors (score: 0.563) |
|
 | | Datalogging with the NXT
|
| OK, I've got to admit that this isn't exactly "robotics". In fact, it must be about the smallest "robot" I've ever made, in that it was really just the NXT and a single sensor, with a few 3L pins and a studless beam to secure the sensor. But the (...) (19 years ago, 31-Oct-07, to lugnet.robotics)
| |
|   sensor (score: 0.563) |
|
| |
|   sensor, sensors (score: 0.563) |
|
 | | c++, classes
|
| Hallo! I try to write a class for legOS in c++. The constructor should get parameters for the used ports for a motor and two sensors, which are private components of the class. Then the contructor should assign these given ports to the private motor (...) (26 years ago, 4-Apr-01, to lugnet.robotics.rcx.legos)
| |
|   sensor, sensors (score: 0.563) |
|
 | | Ultrasonic sensor calibration settings
|
| Hi, Has anyone tried using the standard NXT Ultrasonic sensor calibration settings? I've been doing a little work on the leJOS i2c interface and although I can read both the factory default values and the current settings I do not seem to be able to (...) (19 years ago, 17-Oct-07, to lugnet.robotics.nxt.nxthacking)
| |
|   sensor (score: 0.563) |
|
| |
|   sensor, sensors (score: 0.563) |
|
 | | NXT Developer Kits released!
|
| As prior LEGO press releases (URL) have stated>, the NXT developer kits would be available in August. And here they are! (URL) Software Developer Kit (SDK) Includes the NXT driver interface specification and necessary tools for creating third-party (...) (20 years ago, 1-Aug-06, to lugnet.robotics, lugnet.robotics.nxt, FTX)
| |
|   sensors (score: 0.562) |
|
 | | Re: Scout Commands
|
| (...) If you use NQC then you can write a small program and load it into the Scout...then it behaves much like the RCX. The Scout has VERY little free memory - but it's enough to allow it to act as a dumb peripheral, turning motors on and off and (...) (26 years ago, 4-Apr-01, to lugnet.robotics)
| |
|   sensor, sensors (score: 0.562) |
|
 | | Shutting off illumination LED on Light Sensor for LIDAR
|
| Has anyone successfully found a way (short of paint, or cutting internal wiring) of shutting off the red 'supply light' LED on the Lego light sensor? The supply LED is great for active-detection situations, like line-following, when you need to (...) (26 years ago, 28-Mar-01, to lugnet.robotics)
| |
|   sensor, sensors (score: 0.561) |
|
| |
|   sensor, sensors (score: 0.561) |
|
 | | Re: light sensor multiplexer
|
| Hi Rainer What I do is that switch the power to silected sensor only I do it by using FET. since there is not enough power for all sensors. so when you switch to sensor 2 other sensors are kept off. there is enough power for one sensor since my (...) (26 years ago, 20-Mar-01, to lugnet.robotics.rcx)
| |
|   sensor, sensors (score: 0.561) |
|
| |
|   sensor, sensors (score: 0.561) |
|
| |
|   sensor (score: 0.561) |
|
 | | Re: Robot navigation - barcode stations?
|
| I think it's an excellent idea... I saw the barcode system being explained some years ago and I still think it can be the most accurate. One thing that's different in the system I saw was that there were no LED's used (not needed...) and it would (...) (26 years ago, 29-Mar-01, to lugnet.robotics.rcx)
| |
|   sensor, sensors (score: 0.560) |