|
 | | Re: What to buy...
|
| (...) Of the remaining sensors, a second light sensor and a couple of rotation sensors would be high on my list. There is also a thermal sensor - but I doubt that's of much use unless you have a really specific project in mind that needs it. The (...) (26 years ago, 9-May-01, to lugnet.robotics)
| |
|   sensor, sensors (score: 0.575) |
|
 | | Re: Lego Camera and legOS
|
| Hi, There are two versions of the Logitech QuickCam Express which use two different sensors and as far as I know, only one of them is supported by the alpha driver for Linux. I think that the Lego Cam (and your camera, maybe)uses the other sensor... (...) (25 years ago, 22-May-01, to lugnet.robotics.rcx.legos)
| |
|   sensor, sensors (score: 0.575) |
|
 | | What to buy...
|
| Hi. I have both the Cybermaster and the RCX, which come with several touch sensors and a light sensor. What sensors are the best to add? I was thinking of rotation sensors, but they seem to be difficult to get, and quite expensive too. Any (...) (26 years ago, 9-May-01, to lugnet.robotics)
| |
|   sensor, sensors (score: 0.575) |
|
| |
|   sensor (score: 0.575) |
|
 | | Speed Computer?
|
| It is not seperable. The wire comes out of the little sensor and goes straight into the display part. I had wondered the same thing. But I have not taken it apart yet! I ended up making my own rotation sensors using mouse parts. You get about 4 (...) (26 years ago, 11-May-01, to lugnet.robotics)
| |
|   sensor, sensors (score: 0.574) |
|
 | | Re: Lego/RCX IRPD
|
| John, I am working on a setup that Rainer Balzerowski and Stephen Edwards havew talked about to allow for up to 15 sensor. My ideal design uses about 7 sensors. Two crossing in the front, Two crossing in the back One pointing to each side and One (...) (26 years ago, 17-May-01, to lugnet.robotics)
| |
|   sensor, sensors (score: 0.574) |
|
 | | RSRA-2008
|
| I have been working with a Home Schooler named Ian, to create a Robotic Arm. The Arm was created over a 4 session building period. I call it the RSRA-2008. (URL) The Arm consists of primarily black Technic construction. It utilizes x3 9v geared (...) (19 years ago, 18-Jan-08, to lugnet.technic, lugnet.robotics, FTX)
| |
|   sensor (score: 0.574) |
|
| |
|   sensors (score: 0.574) |
|
 | | NBC with NXT - crash!
|
| Hi, I wrote the following program, and it causes my NXT to crash! If I remove the ReadSensor() call from thread check_sensors, it doesn't crash. If I put a call to ReadSensor() in thread main, it doesn't crash. I tried putting mutexes around all the (...) (20 years ago, 21-Oct-06, to lugnet.robotics.nxt)
| |
|   sensors (score: 0.574) |
|
 | | Re: NBC with NXT - crash!
|
| (...) Running this program on my NXT does not cause mine to crash. Are you definitely running the 1.03 firmware? You can see the version using Settings|NXT Version on the NXT or from the Diagnostic window in BricxCC. My brick shows 01.1240/01.03 in (...) (20 years ago, 21-Oct-06, to lugnet.robotics.nxt)
| |
|   sensors (score: 0.574) |
|
 | | Re: Active sensor scanning by RCX
|
| It reads all three during the brief measurement period once every three milliseconds. In fact, it reads them in reverse order, certainly while running the standard Lego firmware. I think, under LegOS, you can change the rules completely if you want (...) (26 years ago, 4-May-01, to lugnet.robotics)
| |
|   sensor, sensors (score: 0.573) |
|
| |
|   sensors (score: 0.573) |
|
 | | Re: Hi
|
| In article <200610160848.AA1377...v-ed.com>, Yudi Mintoro <lego-robotics@crynwr.com> writes (...) Hi Yudi (...) The conversion cables are available, at least in some regions, here; (URL) think the sensors will all work from the NXT. From NXT-G (...) (20 years ago, 17-Oct-06, to lugnet.robotics)
| |
|   sensors (score: 0.573) |
|
 | | Re: NXT-G using RCX items.
|
| (...) Well, you need converter cables of some sort to even connect RCX sensors and motors to the NXT. Beyond that, I'm not sure; I've not tried yet, because I don't have the converter cables to try. I suspect you will need the special NXT-G (...) (20 years ago, 13-Oct-06, to lugnet.robotics.nxt)
| |
|   sensors (score: 0.573) |
|
| |
|   sensor (score: 0.573) |
|
 | | NXT-G using RCX items.
|
| Hello Everyone: I just read the press release regarding the LEGO Mindstorms Education NXT. There is no discount available for their software that allows me to use my RCX motors, sensors etc with the NXT-G. Do I even need their version to run RCX (...) (20 years ago, 13-Oct-06, to lugnet.robotics.nxt)
| |
|   sensors (score: 0.573) |
|
 | | Re: RCX Solenoid
|
| That is a very complex project. The rotation sensor will provide you with positioning information. It does lose counts sometimes, so it is best to reset the counter often. If you have not already seen this site, take a look at (URL) is a lot of (...) (26 years ago, 12-May-01, to lugnet.robotics)
| |
|   sensor, sensors (score: 0.572) |
|
 | | Re: RCX Solenoid
|
| (...) sounds interesting. if you could find links or more info, it´d be great. My plans for building a sculpting machine sofar is pretty simple and straightforward. i am (or we are) basically trying to build a plotter that pours material down on the (...) (26 years ago, 12-May-01, to lugnet.robotics)
| |
|   sensor, sensors (score: 0.572) |
|
| |
|   sensor (score: 0.572) |
|
 | | Re: Ultrasonic sensors
|
| I also have the utrasonic sensor. These things work great, although every robot that I build that uses them uses the sensor for a specific task, so I don't think that these need to be put on my as-of-yet non-existant website. Does anybody else use (...) (26 years ago, 4-May-01, to lugnet.robotics)
| |
|   sensor, sensors (score: 0.572) |