 | | Re: micro motor sometimes stuck
|
|
The micro motor doesn't have an axle output, just a standard stud. David Kadansky wrote in message <3760AC13.5079426F@p...ox.com>... (...) (27 years ago, 11-Jun-99, to lugnet.robotics)
|
| |
 | | (canceled)
|
|
|
| |
 | | Lego Mindstorms in China
|
|
I have heard that M.I.T. students are comming to China to set up a Lego Robotics League. I would like to talk to some of the students in Beijing so that they can give me ideas for projects for the new Mars Pathfinder. I will make a new robot for you (...) (27 years ago, 11-Jun-99, to lugnet.robotics)
|
| |
 | | Sorry for the double posting
|
|
Hi Todd (or anyone else in charge), I was with Marcus when he wrote the two letters on Mindstorms in China. First he posted one - and got an error message. Later he posted a new one - and got another error message. After that I wanted to re-submit (...) (27 years ago, 11-Jun-99, to lugnet.robotics)
|
| |
 | | Re: micro motor sometimes stuck
|
|
(...) I recall reading somewhere (but I can't remember where) that the micro- motor has an internal switch to protect it from stall current. If you hold it up to your ear when it's stuck and apply power, you can hear a small click, I think. Haven't (...) (27 years ago, 11-Jun-99, to lugnet.robotics)
|
| |
 | | Re: Sorry for the double posting
|
|
(...) Franz-Michael, Do you recall what error message Marcus received when he posted? Also, is it possible that he pressed the 'Esc' key or the browser's 'Stop' button while posting the first message, upon realizing that it was missing his site's (...) (27 years ago, 11-Jun-99, to lugnet.robotics, lugnet.admin.general)
|
| |
 | | Re: micro motor sometimes stuck
|
|
(...) The slippage is supposed to occur between the micro motor and the pulley, not the pulley and the axle. The micro motor uses a stud (rather than an axle) as its output, and you insert that stud into the rubber lining. Cheers, Hao-yang Wang (27 years ago, 11-Jun-99, to lugnet.robotics)
|
| |
 | | adam@hpnc.com
|
|
I went to helitex today and they has sent out a check yesterday by mail. I should get it monday I think. Also Gary said that it is still not emailing him the orders. Didnt you say you changed the email address to heli212@waymark.net Could you please (...) (27 years ago, 12-Jun-99, to lugnet.robotics)
|
| |
 | | Thanks ...Re: Removing red led from light sensor..
|
|
Thanks for all the advice. I got the parts from radio shack and just made a new light sensor today. Now its time to start working with NQC or GORDON'S BRICK PROGRAMMER or somthing. Patrick Lawrence wrote in message ... (...) (27 years ago, 12-Jun-99, to lugnet.robotics)
|
| |
 | | GORDON'S BRICK PROGRAMMER
|
|
Just wandering if any one was using GBP? (27 years ago, 12-Jun-99, to lugnet.robotics)
|
| |
 | | Wheel Setup for the 8880
|
|
Has anyone came up with a good way to use the wheel assemblies that come with the 8880 with smaller tires (the 68.8 x 40 Q)? -- Clay Aucoin (27 years ago, 12-Jun-99, to lugnet.robotics)
|
| |
 | | sorry about the message to adam longggg day
|
|
(27 years ago, 12-Jun-99, to lugnet.robotics)
|
| |
 | | Re: Wheel Setup for the 8880
|
|
(...) It is probably not feasible. You may note, however, that the 2x2 round plate with cross axle hole fits into the hole in the white steering gear from 8880. Perhaps this fact can be used for something useful? Let us know if you can get something (...) (27 years ago, 12-Jun-99, to lugnet.robotics)
|
| |
 | | Re: Wheel Setup for the 8880
|
|
Yeah but only the posts fit..and not really that good.. (...) -- ---- Clay Aucoin (27 years ago, 12-Jun-99, to lugnet.robotics)
|
| |
 | | Re: GORDON'S BRICK PROGRAMMER
|
|
(...) Gordon's Brick Programmer is easy to use. You have way more command choices than in Lego Mindstorms and the commands are easier to use. It also does not take as much time making a program on Gordon's Brick Programmer as on Lego Mindstorms. You (...) (27 years ago, 13-Jun-99, to lugnet.robotics)
|
| |
 | | Re: Problems with RCX, ROBOLAB and Macintosh
|
|
Hallo, I have tried NEW batteries in ir tower and RCX. I have tried to communicate in an absolute dark room with the same results. The ir tower is in near mode and the RCX in reset mode (take out the batteries and switch on the RCX - put the (...) (27 years ago, 6-Jun-99, to lugnet.robotics)
|
| |
 | | Anyone have any luck making a successful floating boat?
|
|
I was just wondering if anyone has had (or even tried) making a successful floating boat (not using the "Boat Really Floats" pieces)? -- Clay Aucoin (27 years ago, 14-Jun-99, to lugnet.robotics, lugnet.build)
|
| |
 | | Fw: Problems with RCX, ROBOLAB and Macintosh
|
|
I've seen this thread going, and going, and going; must be pretty frustrating. It seems like you said at one point that it works fine from a PC, is that right? If so, don't you have to use a serial adapter to connect the IR tower to a Mac? And if (...) (27 years ago, 13-Jun-99, to lugnet.robotics)
|
| |
 | | Re: Problems with RCX, ROBOLAB and Macintosh
|
|
Hallo Will, it can't be the adapter cable which is wrong. With NQC -the very good programming software from Dave Baum- I have no problem to contact the RCX. Downloading the firmware, sending programs, starting programs ... it's okay. Everything (...) (27 years ago, 14-Jun-99, to lugnet.robotics)
|
| |
 | | Re: Anyone have any luck making a successful floating boat?
|
|
(...) I've considered using empty air tanks from pneumatic LEGO sets as sort of 'pontoons'... my one quick test of this so far was too top-heavy (I only have three air tanks), but it seems like it should work, as long as the floats are far enough (...) (27 years ago, 14-Jun-99, to lugnet.robotics)
|