To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 4361 (+10)
  Re: multi-device output controller (fwd)
 
----- Forwarded message from Bill Flanagan ----- From: "Bill Flanagan" <bflanagan@mediaone.net> Subject: Re: multi-device output controller (fwd) Date: Fri, 26 Mar 1999 12:33:18 -0500 OK now the details. 6. Send to a MAX232 devices and wallah, (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller (fwd)
 
(...) [snip] (...) Dunno, I haven't looked yet, I just came up with the idea. (...) Because I felt like it? I've seen it written both ways. [snip] (...) Nope. 0 (speed) means off, no matter what direction you are going, therefore: 0= forward, (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Stepper motor design
 
----- Forwarded message from Wes Matchett ----- From: Wes Matchett <wes@augustschell.com> Subject: Re: multi-device output controller Date: Fri, 26 Mar 1999 17:34:25 GMT Now that I have brought up that topic, anyone know how to drive a stepper motor (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller
 
In my example the RCX output was just used to tell this mythical board which output to drive. Power for the output came from a battery box, always set to on. The RCX can't set direction on the battery box (at least not trivially). alex (...) -- Did (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller
 
(...) Are you sure? I wasn't, so I went looking. The NQC docs seem to imply 7 powers levels plus off. Which, technically, is 8 levels of PWM, but if you use all of them, a motor is running at all times. That is fine if you use another motor output (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller
 
Right. That is why you cannot use all 8 power levels. The polarity reversal that I am talking about is on the controlling (and only) output. I am already assuming, at this point, that drive power is stuck on as with your external battery box. (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller
 
(...) I don't know how NQC drives the ports, but both rcxcc and the RIS software have separate controls for on/off and power level. I just tested setting all 8 power settings - motors operates for all 8. -Wes (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: Stepper motor design
 
(...) It realy depends on what form of stepper motor you are using and how the coils are wired up. if you can arange it as two sets of coils you could drive it by hooking one motor output up to one pair of coils and the second motor output up to the (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller
 
Thanks for checking this out. This is important to know. I assume, then, that the duty cycles are 1/8 through 8/8 as well as off, which would be 0/8. Can anybody verify this (with a scope or something)? I have long wondered whether the duty cycles (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
 
  Re: multi-device output controller (fwd)
 
How about an RCX to RS232 connection to use off the shelf components? Check out this link. (URL) sells a simple serial servo contol that services up to 8 motors via an rs232 port ($49.95). I have seen a simple version adapted for a Palm Pilot for (...) (28 years ago, 26-Mar-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR