 | | Re: Thoughts on Turning
|
|
(...) yup, and the 2nd design on there (my dad's design) doesn't require 5 length axles anyway. i knew that i could get 5length axles, i just didn't have any (they are a bit rare still) and cut up a 10 length axles. i can remember doing the same (...) (28 years ago, 25-Jan-99, to lugnet.robotics)
|
| |
 | | IrDA anyone ?
|
|
I wonder would it be possible to communicate with the RCX using an IrDA compliant IR port such as ones on Notebooks or H/PC. I know someone had done it with his HP palmtop. Is IrDA standard IR port operating within the bandwidth of the RCX IR port ? (...) (28 years ago, 25-Jan-99, to lugnet.robotics)
|
| |
 | | Re: DATALOG and C
|
|
(...) SetDatalog is listed in the SDK page 91 as an Immediate Command. If that is true then, if you put the command in with some downloadable RCX instructions, it does whatever it does right then and is not actually sent with the RCX program. (...) (28 years ago, 25-Jan-99, to lugnet.robotics)
|
| |
 | | Re: DATALOG and C
|
|
(...) I believe that the maximum size of the datalog is 2033 entries, minus whatever you need for program data. If you want to figure this out dynamically from the PC, get the memory map after downloading all programs to the RCX. The maximum datalog (...) (28 years ago, 25-Jan-99, to lugnet.robotics)
|
| |
 | | Using motors without a power source.
|
|
I'm new to this group so I don't know if this idea has been mentioned but here it is: First, I connect the two motors in the MindStorms kit together with a wire and nothing else. Below is a crude ASCII art representation: ***...*** ***...*** * * (...) (28 years ago, 25-Jan-99, to lugnet.robotics)
|
| |
 | | Re: Using motors without a power source.
|
|
(...) In this case one motor is being used as a generator and the other as a motor, correct? You aren't powering both motors. I think its neat, but don't understand the use of it in the context of 4wd. The differential is much smaller then two (...) (28 years ago, 25-Jan-99, to lugnet.robotics)
|
| |
 | | Re: Thoughts on Turning
|
|
(...) *shudder* Despite my not-quite-purist's outlook, cutting Legos up if the thing you make are already available otherwise just freaks me out :) well, I just recently ordered some Service sets: 2 gear sets, 2 small beam sets, 2 axle sets, and two (...) (28 years ago, 25-Jan-99, to lugnet.robotics)
|
| |
 | | Re: Thoughts on Turning
|
|
Alex I read your message and went to your web page and looked at your desigh and was wondering if you (or anyone else) can help me with resources for building robots for my 16 year old son. We Home school and are about to start using mindstorms for (...) (28 years ago, 25-Jan-99, to lugnet.robotics)
|
| |
 | | Re: Thoughts on Turning
|
|
I made a wheel that could roll sideways. That way you don't have to raise and lower the turn wheel. Check out "Curvy1" at (URL) It needs some refinement, but the idea works. Bill Jasper Janssen wrote in message <36ac7ccf.83855140@l...et.com>... (...) (28 years ago, 25-Jan-99, to lugnet.robotics)
|
| |
 | | Re: IrDA anyone ?
|
|
Hello My name is Jin Sato, One of Japanese MindStorms mania. I have to apologize my English is limited. (Japanese is mother tongue) BTW. On Mon, 25 Jan 1999 17:02:02 +0000 "Kin W. Lau" <kin.lau@ic.ac.uk> wrote: Actually. we created program for (...) (28 years ago, 25-Jan-99, to lugnet.robotics)
|