 | | Re: Replacement Firmware Released
|
|
(...) Agreed. For practical reasons, Ultimate Robolab implements the variable brake mode too. (22 years ago, 24-Dec-04, to lugnet.robotics)
|
| |
 | | Re: Replacement Firmware Released
|
|
(...) I don't think this is a bug in the original firmware, but rather a protection against burning electronics parts in the RCX or dammaging motors flipping the motor directions too rapidly. Motors present some interesting electronics behaviour due (...) (22 years ago, 24-Dec-04, to lugnet.robotics)
|
| |
 | | Re: Replacement Firmware Released
|
|
I'm pretty sure that variable strength braking is in fact the implementation in the standard firmware. Braking is proportional to the current setting of the power level. I think there may even be some ancient posts somewhere in Lugnet on this topic. (...) (22 years ago, 23-Dec-04, to lugnet.robotics)
|
| |
 | | Re: Replacement Firmware Released
|
|
The behavior you've experienced is expected. Standard Lego firmware implements a 100 msec delay when you directly "flip" or change powered motor direction. I expect it is a bug (rather than design intent) that if you go through the stage (...) (22 years ago, 23-Dec-04, to lugnet.robotics)
|
| |
 | | Re: Replacement Firmware Released
|
|
Hi Dan, (...) that is strange, are you sure? (...) That is what the ROM routines do, and firmwares like Lejos that rely on it. I would have thought the standard firmware does it in the same way. Jürgen (22 years ago, 23-Dec-04, to lugnet.robotics)
|
| |
 | | Re: RCX IR Transceiver and Sensor Port Circuits
|
|
Hi Mark, (...) I would also like to see your diagrams. (...) Please use GIF or PNG, jpegs are not so good for diagrams. Jürgen (22 years ago, 23-Dec-04, to lugnet.robotics)
|
| |
 | | Re: Replacement Firmware Released
|
|
(...) Indeed, it vibrates fine if you set nMotorTransitionDelay = 0 Philo (22 years ago, 23-Dec-04, to lugnet.robotics)
|
| |
 | | Re: Replacement Firmware Released
|
|
(...) Agreed. Beeing able to control break strength is an interesting feature, but it is incompatible with standard firmware. Maybe it should be controlled by a variable similar to bFloatDuringInactiveMotorPWM (22 years ago, 23-Dec-04, to lugnet.robotics)
|
| |
 | | Re: Replacement Firmware Released
|
|
(...) I did exactly the same thing today, and found I needed a figure of about twenty to acheive reliable back and forth motion. I think it may be something to do with the fact that the rcx firmware(s) will not let you switch motor direction (...) (22 years ago, 23-Dec-04, to lugnet.robotics)
|
| |
 | | Re: Replacement Firmware Released
|
|
I too am impressed with the amount of work that went into this release. After a few days playing around with it, I have a few comments: 1) braking seems to be proportional to power (at power=0, brake is not very effective) -- Lego firmware appears (...) (22 years ago, 23-Dec-04, to lugnet.robotics)
|
| |
 | | Re: RCX IR Transceiver and Sensor Port Circuits
|
|
(...) I'll see if I can get the circuits drawn up as jpegs and post them on my Brickshelf. Can't promise a schedule though :-) The IR Transceiver will be first, followed by a sensor port circuit. The other units are just possible future projects for (...) (22 years ago, 22-Dec-04, to lugnet.robotics)
|
| |
 | | Some new Mindstorms MOC's
|
|
I have posted a few new Mindstorms MOC's to my site... Specifically, TrackerBot and PicoCam which use a custom DIRPD sensor, 3 Cybermaster touch sensors and a wireless colour pinhole camera. Have a look and don't forget to drop a line in my (...) (22 years ago, 22-Dec-04, to lugnet.robotics)
|
| |
 | | Re: RCX IR Transceiver and Sensor Port Circuits
|
|
I for one would look at your work if posted on some web site. Lamar ----- Original Message ----- From: "Mark Bellis" <mark.bellis@tiscali.co.uk> To: <lego-robotics@crynwr.com> Sent: Friday, December 17, 2004 9:49 AM Subject: RCX IR Transceiver and (...) (22 years ago, 21-Dec-04, to lugnet.robotics)
|
| |
 | | Re: CC2: discus, Hammerhead the CD thrower
|
|
(...) ...and now LDraw files! Philo (22 years ago, 19-Dec-04, to lugnet.robotics, lugnet.technic)
|
| |
 | | Re: RCX IR Transceiver and Sensor Port Circuits
|
|
(...) i would like to encourage you to publish your knowlegde, as there is - as far, as i know - no other source of information about that subject in the internet today. So, you would be the first! I am very interested in seeing your diagrams. (...) (22 years ago, 18-Dec-04, to lugnet.robotics)
|
| |
 | | Re: RCX IR Transceiver and Sensor Port Circuits
|
|
Hello Mark, (...) _You_ have beaten me ;o) That was something I intended to do someday... Yes, I would definitely be interested by your diagrams! Philo (22 years ago, 18-Dec-04, to lugnet.robotics)
|
| |
 | | Re: Brute Force Brick
|
|
(...) They still seem to be available from Lego Education, at least: (URL) They're $10 for a set of three, which is $1.67 per terminal. Best, - Joe (22 years ago, 18-Dec-04, to lugnet.robotics)
|
| |
 | | RCX IR Transceiver and Sensor Port Circuits
|
|
I've not seen much online in the way of circuits of the RCX transceiver or parts of the RCX itself. Everyone seems too busy reprogramming it! I have dismantled the units and traced the connections, found out the pin-outs and equivalent components (...) (22 years ago, 17-Dec-04, to lugnet.robotics)
|
| |
 | | Re: Brute Force Brick
|
|
Joe Strout wrote: > Can we hack apart LEGO connection (...) Didn't Lego also stop selling bulk packs of wires too? I thought I read that somewhere here. ---...--- Steve Baker ---...--- HomeEmail: <sjbaker1@airmail.net> WorkEmail: <sjbaker@link.com> (...) (22 years ago, 17-Dec-04, to lugnet.robotics)
|
| |
 | | Re: Brute Force Brick
|
|
(...) I do see this as a pretty big impediment to custom LEGO electric parts. I've run into this myself, just trying to make some simple light units. My solution was this: Using silver paint, paint leads on the side of a 2x2 brick (with the center (...) (22 years ago, 17-Dec-04, to lugnet.robotics)
|