To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 22624 (-20)
  Re: challenge: LEGO copier
 
(...) OK, just to clarify: assume an X-Y-Z space with studs sticking up in the Z direction. You mean a model that's only one stud thick in X, arbitrarily wide in Y, and arbitrarily high in Z? Yes, that would be a much simpler problem than what I was (...) (22 years ago, 4-Aug-04, to lugnet.robotics)
 
  Re: challenge: LEGO copier
 
(...) The closest I got to something like that was my half-built Duck Assembly Carousel - a dial automation with 4 positions, which would assemble the body (2x1 inverted slope), beak (2x1 plate), and head (1x1 brick with a hole in it). I didn't have (...) (22 years ago, 4-Aug-04, to lugnet.robotics)
 
  Re: challenge: LEGO copier
 
Would the bricks be assembled as a wall one brick thick on its side? Like laying a cinderblock wall on its side then creating a copy? That might be done with an X-Y table arrangement with vice like sides at top and bottom of the bricks so that they (...) (22 years ago, 4-Aug-04, to lugnet.robotics)
 
  Re: challenge: LEGO copier
 
(...) There are some clever tricks (diff & ratchet/clutch, muxes) to expand it somewhat for some applications, but in general, yes, a single RCX can drive only three independent pulse-width modulated polarity reversible 9V outputs. -SMQ Shawn (...) (22 years ago, 4-Aug-04, to lugnet.robotics)
 
  Re: challenge: LEGO copier
 
(...) No, I meant stuck to each other. (...) That's what I had in mind too. (...) I was assuming the use of a camera, not the LEGO light sensor. But using the light sensor is a clever idea. (...) Here I expose my complete cluelessness with regard to (...) (22 years ago, 4-Aug-04, to lugnet.robotics)
 
  Re: challenge: LEGO copier
 
(...) I wasn't thinking that the bot would have to exactly reproduce which same-color bricks are used side-by-side -- if I used a two 1x2 bricks, but the robot chooses to substitute a 1x4 brick, in my mind that's the same model. We'll just say the (...) (22 years ago, 4-Aug-04, to lugnet.robotics)
 
  Re: challenge: LEGO copier
 
(...) Actually, he said "flat". So I would assume that he meant an assortment of bricks simply stuck to one baseplate, sort of like a mosaic. As for brick boundaries... I think the only thing you would need to worry about is the boundaries where the (...) (22 years ago, 4-Aug-04, to lugnet.robotics)
 
  Re: challenge: LEGO copier
 
(...) Here's an easy 'rule' you could add to resolve that. Just say that a given color may only be used for one size/type of piece. You don't even have to specify what colors are used, as long as any color may only represent one piece type. To make (...) (22 years ago, 4-Aug-04, to lugnet.robotics)
 
  Re: challenge: LEGO copier
 
(...) Ugh. Much harder than it sounds: either the robot needs extreme visual acuity to spot the brick boundaries (so it can tell two 1x2 bricks of the same color end-to-end from a single 1x4 brick... or, more importantly, which order a 1x1 and a 1x4 (...) (22 years ago, 4-Aug-04, to lugnet.robotics)
 
  challenge: LEGO copier
 
Here's an idea I am certainly not equipped to attempt, but I bet somebody is... The user builds some model (constraints: it must be composed of a 1x1, 1x2, and 1x4 bricks in a selection of several colors, and must be flat, i.e. two-dimensional, and (...) (22 years ago, 4-Aug-04, to lugnet.robotics)
 
  Re: Pneumatics Vs. Hydraulics
 
(...) Take two valves, two 2cm tubes with an antenna stuck in the end, a 8cm tube and input and output tubes. Arrange the valves so that they switch together, using "1" joints on their levers, connected by a liftarm (centres 32mm apart for old (...) (22 years ago, 2-Aug-04, to lugnet.robotics)
 
  Re: Pneumatics Vs. Hydraulics
 
(...) I'm not clear on this. It sounds interesting, I just can't picture how it's done. Where does the tube go? Is it acting like a little variable volume reservoir? (...) I agree completely here. Hydraulics would be *much* more complicated, (...) (22 years ago, 2-Aug-04, to lugnet.robotics)
 
  Re: Pneumatics Vs. Hydraulics
 
Thank you much! (22 years ago, 27-Jul-04, to lugnet.robotics)
 
  Re: Pneumatics Vs. Hydraulics
 
(...) One way to change pressure in Lego pneumatics by a small amount is to switch in a short tube (2cm) with an antenna stuck in the end. This lets only a small amount of air out of the cylinder, whilst not exhausting any to the atmosphere. (...) I (...) (22 years ago, 31-Jul-04, to lugnet.robotics)
 
  Re: USB Tower
 
Hi Alberto, (...) yes, and I take care of the driver as of 2.6.6 . You really don't need the LEGO Software. (If you just want the driver you can get the RCX SDK 2.5.) Jürgen (22 years ago, 30-Jul-04, to lugnet.robotics)
 
  Re: USB Tower
 
(...) That was not the idea... (...) If I can make it work on linux, I'll not need the windows software O:-) So, first let me test it. Then, I'll contact LEGO. Thanks. (22 years ago, 30-Jul-04, to lugnet.robotics)
 
  Re: USB Tower
 
(...) Nice. I'll try to do that. If I can't make it work, I'll anoy you to help me :-) THanks, (22 years ago, 30-Jul-04, to lugnet.robotics)
 
  Re: USB Tower
 
(...) It doesn't sound like Alberto was trying to break the law. Alberto, at one point, LEGO was selling an upgrade kit for about $25. Their customer service is very helpful. If you contact them, they should be able to tell you how to get the (...) (22 years ago, 30-Jul-04, to lugnet.robotics)
 
  Re: USB Tower
 
(...) Yup... I've been using LeJOS and the USB based tower in Linux in 2.6.x since January or so of this year. (...) Actually, it not only sounds like piracy, what you are suggesting _is_ piracy. Sorry... you are asking someone to do something that (...) (22 years ago, 30-Jul-04, to lugnet.robotics)
 
  USB Tower
 
Hi I have a 1.5 invention set with a serial tower. Meanwhile, my laptop do not have a serial plug. Then, I brought a usb tower. Now, I would like to know: - anybody using usb tower with linux kernel 2.6.x? - although this can sound as piracy, can (...) (22 years ago, 30-Jul-04, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR