To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 22559 (-20)
  Re: BrickFest is coming!
 
I'm reposting this message to the events.BrickFest list so that everyone knows about this great opportunity. I'm sure there are others out there, just like me, who have an RCX set (found for a good price, or a gift, whatever the case...) and you (...) (22 years ago, 25-Jun-04, to lugnet.events.brickfest, lugnet.announce, lugnet.technic, lugnet.robotics)
 
  BrickFest is coming!
 
... and there are competitions to be entered and won! Check out the Events at www.brickfest.com There's a link via Mindstorms Competitions to the event descriptions and from there to the rules pages. So read them and start building! ... there are (...) (22 years ago, 22-Jun-04, to lugnet.technic, lugnet.robotics)  
 
  Re: is it possible to make a motor with a limited range of travel?
 
(...) It will help us help you if you list the resources you have and how many of these you need to make. If your resources are limited, you may have to use a few different solutions to match your inventory. Kevin (22 years ago, 20-Jun-04, to lugnet.robotics)
 
  Re: is it possible to make a motor with a limited range of travel?
 
(...) bricks along the beam, like I did on my tower crane (URL) (22 years ago, 20-Jun-04, to lugnet.robotics)
 
  Re: is it possible to make a motor with a limited range of travel?
 
"Brass Tilde" <lego-robotics@crynwr.com> wrote in message news:00a301c4552c$24...hps.net... <snip> (...) I built something very much like this. I used a rack with a few 1x1 TECHNIC beams in it. The touch sensor pressed against the side of the rack (...) (22 years ago, 18-Jun-04, to lugnet.robotics)
 
  RE: is it possible to make a motor with a limited range of travel?
 
(...) belt. (...) Hello, If you take a beam and put racks on it, you can push that across a gear and it will make the gear spin. A back and forth motion causes back and forth rotation on the gear. To get mechanical back and forth motion, simply (...) (22 years ago, 18-Jun-04, to lugnet.robotics)
 
  Re: is it possible to make a motor with a limited range of travel?
 
(...) There are some methods involving non-lego peices in the mix. One such method, is to build a touch sensor using a microswitch from a mouse. Wire this in the normally closed way - so when it is activated, it will open. So the motor will go the (...) (22 years ago, 18-Jun-04, to lugnet.robotics)
 
  Re: is it possible to make a motor with a limited range of travel?
 
(...) Or you may use poor man's clutch gear: pulleys and slipping rubber belt. Or if your application does not need too much mechanical power, you can simply use a low power level on RCX output. With a power level 2 both the RCX and the motor can (...) (22 years ago, 18-Jun-04, to lugnet.robotics)
 
  Re: is it possible to make a motor with a limited range of travel?
 
(...) clutch (...) at (...) You should only need one touch sensor per rack. If you only have one motor per rack, then you should be able to use one sensor per motor (unless you have other stuff you need the sensor ports for, of course). M RRR...RRR (...) (22 years ago, 18-Jun-04, to lugnet.robotics)
 
  Re: is it possible to make a motor with a limited range of travel?
 
(...) Thats kinda usefull except that I dont have enough clutch gears, touch sensors or sensor inputs on my RCX :( (22 years ago, 18-Jun-04, to lugnet.robotics)
 
  Re: is it possible to make a motor with a limited range of travel?
 
Jonathan, What about putting stops on the rack to limit the travel and use a clutch gear to keep the motor from being damaged? Or what about putting a peg at each end of the rack that stick out and hit a touch sensor when the gear rack is close to (...) (22 years ago, 18-Jun-04, to lugnet.robotics)
 
  is it possible to make a motor with a limited range of travel?
 
Basicly, I want a setup where a motor has a gear wheel connected to a long gear rack. Then I want to have things so that holding down the motor buttons (up and down) will move the rack but wont allow it to move off the end of the rack. Anyone got (...) (22 years ago, 18-Jun-04, to lugnet.robotics)
 
  Re: RCX and Micro Scout Communication
 
(...) Gabe, Did you see my other post in this thread? (URL) includes a link to the VLL data format. Using that, it shouldn't be hard to build something that can "talk" VLL to a Spybot. You'd be able to send messages (a number from 1 to 127) from the (...) (22 years ago, 16-Jun-04, to lugnet.robotics)
 
  Re: RCX and Micro Scout Communication
 
(...) So, for instance, if I want to use a spybot to control something else, what VLL codes I can to use? Can it also get info back from the other controller? Can VLL be used to make the spybot talk to some other microcontroller like OOPIC or (...) (22 years ago, 16-Jun-04, to lugnet.robotics)
 
  New RCX alternative ?
 
Hi,All I just got this in my email. It appears that there is a new, more powerful alternative to the RCX available : ) Check out the XRC here : (URL) not affiliated with Charmed Labs in any way, other than being a happy customer. I had purchased an (...) (22 years ago, 14-Jun-04, to lugnet.robotics)
 
  My new website (with some MOC´s)
 
Hi everyone! I want to anounce my new site dedicated to LEGO! Currently, it have only 3 MOC´s, but I hope to make it bigger with the time... I´m also anouncing my new robotic car - with rack-and-pinion steering and rear suspension. You can see the (...) (22 years ago, 13-Jun-04, to lugnet.technic, lugnet.robotics)
 
  Re: Favorite robot ?
 
(...) lugnet.. I started building J5 about a year ago. Since then I I built on im my rare freetime (family an my on company are taken my time away..) On BrickShelf I'm posting some pictures from time to time. J5 isn't finished jet. I think, I will (...) (22 years ago, 11-Jun-04, to lugnet.robotics)
 
  P'titgneugneu the stairs climber, was Re: CC3:Stairs,
 
Here is the (URL) write-up> about the robot I built for CC3:Stairs contest, that happened to win ;o) A bit flimsy, not too pretty, but it did the job! (URL) As the results have not been published here, I inserted the official announcement below. (...) (22 years ago, 10-Jun-04, to lugnet.events, lugnet.robotics, lugnet.technic, lugnet.announce, FTX)
 
  Re: VLL Codes
 
(...) If you want to print out all the codes on one piece of letter sized paper, I have modified the file from (URL) to do so for the Codepilot. It is here (URL) in both Postscript and PDF format. (...) (22 years ago, 7-Jun-04, to lugnet.robotics)
 
  Re: Motor-powered transmission
 
(...) I just built that, but using the instructions, the 20t bevel gear used for 1st gear scrapes one of the 1x8 plates. Moving the plates up to the top solves the problem (I also used 2x8s to help keep it square). HTH ROSCO (22 years ago, 7-Jun-04, to lugnet.robotics, lugnet.technic)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR