To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / 1276 (+20)
  Delphi developers
 
RCX Command Center was written in Delphi using the spirit.ocx. It work very easy. (Only note that the On command to switch motors on is called On_ because on is a reserved word in Delphi.) But if you want to write programs to download to the RCX, I (...) (28 years ago, 10-Dec-98, to lugnet.robotics)
 
  CM: MotorCurrent
 
For the Cybermaster unit, it is possible to monitor the current of the external motor, measured in milliamps. I assume this can be used to detect when the motor is stalled. Do anybody know the typical values of MotorCurrent when the motors is o (...) (28 years ago, 10-Dec-98, to lugnet.robotics)
 
  Re: Communicating with IR tower
 
Hi John, I've been doing this for a while with the Cybermaster. You can simple use the SetVar and Poll commands in immediate mode via the OCX to read and set variables in the brick. Add a bit of handshaking and you have a communications mechanism (...) (28 years ago, 10-Dec-98, to lugnet.robotics)
 
  effect of motor speeds
 
I noticed that settting the motor speed does not seem to have much efect on the speed the robot is moving: 0 = slow 1 = faster 2 = slighly faster than 1 3-7 = about equal to 2 Am I doing something wrong? Or is this standard behavior? Mark Overmars (28 years ago, 10-Dec-98, to lugnet.robotics)
 
  Re: CM: MotorCurrent
 
I only made one test with it, and by the looking at the results I couldn't tell if the motor running loaded, but I may be wrong! The result of the function seems to be: .If no motor is attached, the result is zero. .If a motor is attached and not (...) (28 years ago, 10-Dec-98, to lugnet.robotics)
 
  Re: CM: MotorCurrent
 
(...) Yes, this sounds plausible. My comment on stall detections was probably wrong. Fredrik (28 years ago, 10-Dec-98, to lugnet.robotics)
 
  Re: effect of motor speeds
 
(...) I think so, most problematical is the reduction in starting torque, free running always seems to peak at the same RPM. With an Acrobot based robot I have problems with wrinkles in the carpet stopping it when manoevering at low speed, but it (...) (28 years ago, 10-Dec-98, to lugnet.robotics)
 
  Re: effect of motor speeds
 
(...) I think it depends a lot on the weight of the robot and the type of mobility used. For instants, when I use tracks on my CyberMaster, 1 is very very slow and 7 is fast. All the other numbers between have speeds more or less according to this (...) (28 years ago, 10-Dec-98, to lugnet.robotics)
 
  Re: effect of motor speeds
 
Humm... I think I switched the legends. Laurentino Martins (...) (28 years ago, 10-Dec-98, to lugnet.robotics)
 
  Re: Communicating with IR tower
 
(...) Have you already done this? (detect out of range situations?) I'd really would like to know how did you do it! I also have a CyberMaster and I'm working with NQCC and with the Spirit.OCX in VC++. Thanks! Laurentino Martins (...) (28 years ago, 10-Dec-98, to lugnet.robotics)
 
  Re: Where to buy in London
 
In article <VA.000017c1.05e516c...pthought>, John Cooper <robots@jpsc.co.uk> writes (...) ... and the shop at Legoland Windsor is open until sometime before Christmas. I got mine (well my sons!) the for a 10% discount off UKP160 as he was a lego (...) (28 years ago, 10-Dec-98, to lugnet.robotics)
 
  Out of range
 
[transferred to a new thread] I'm trying to create a good algorithm for detecting out of range situations with the tower, using NQCC. Have anybody already found a good way of doing this? My guess is that this is not possible, but... I have a (...) (28 years ago, 10-Dec-98, to lugnet.robotics)
 
  Wall Street Journal on Lego Mindstorms
 
The Wall Street Journal has a nice (albeit technologically simplified) article today on Lego Mindstorms' popularity among adults. It's not, to my knowledge available on-line, and for copyright reasons I won't post it all here. But here's a couple (...) (28 years ago, 10-Dec-98, to lugnet.announce, lugnet.general, lugnet.robotics)
 
  Re: Out of range
 
Hi, I have some code that does this but it get kind of complicated to explain but here goes.... 1. I have a separate thread in my (C++) app that is used to poll the cybermaster variables. I can set which variables to check under program control. 2. (...) (28 years ago, 10-Dec-98, to lugnet.robotics)
 
  Re: 2 RCX communication on the same model
 
(...) You mean the RIS/GUI language? It _does_ have an IR message function. (28 years ago, 10-Dec-98, to lugnet.robotics)
 
  Pre-LEG British bricks
 
What again was the name of the British bricks back when LEGO started? What again was the webpage with pictures of them? Eric Brok (28 years ago, 10-Dec-98, to lugnet.robotics)
 
  Re: Wall Street Journal on Lego Mindstorms
 
(URL) has this article for subscribers. I found it by searching for Mindstorms. It doesn't give back a URL useful for anyone else, but others can probably the article by doing the same search. alex (28 years ago, 10-Dec-98, to lugnet.robotics)
 
  Re: Pre-LEGO British bricks
 
Eric Brok wrote in message ... (...) To answer my own questions: Kiddicraft (URL) Brok (28 years ago, 10-Dec-98, to lugnet.robotics)
 
  legOS-0.1.3
 
Hello, legOS now supports active light sensors. Newest version at: (URL) is an unofficial native mode kernel for the Lego Mindstorms RCX. It features preemptive multitasking, energy saving, dynamic memory management, POSIX semaphores, native access (...) (28 years ago, 10-Dec-98, to lugnet.robotics)
 
  Re: What is LabView like?
 
Being a Mac user I haven't had much of a chance to play with the software provided by Lego but I did play with RoboLab some. One of the big differences I could see is that RoboLab is more "verbose" than the Mindstorm stuff. For example, if you want (...) (28 years ago, 10-Dec-98, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR