 | | Re: gleason research experiences?
|
|
[Carlos Puchol] spake unto the ether: (...) We bought about 25 Handy Boards from Gleason Research almost 2 years ago. One of them had a mis-seated MAX232 (or whatever it is) chip on the serial board, so that was the only one that didn't work (...) (28 years ago, 16-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Recommended Add-On Sets?
|
|
(...) The 779928/779927 Beams packages from Lego Dacta come with 4 each of the #16, #12, #10, #8, and #6 beams as well as 8x #4 and 16x #2 beams. At least in what I have done so far, I wind up needing as many of the #12 beams as I do the #16 beams. (...) (28 years ago, 16-Feb-99, to lugnet.robotics)
|
| |
 | | RE: Recommended Add-On Sets?
|
|
(...) Anybody in the know of U.S. sources for the cannons (either in sets or sold separately as in the supplementary catalog listed above)? -- Did you check the web site first?: (URL) (28 years ago, 17-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Recommended Add-On Sets?
|
|
Commotion have a website www.commotion.co.uk but it is undergoing changes at present. John. (28 years ago, 17-Feb-99, to lugnet.robotics)
|
| |
 | | Motor power?
|
|
When I set the motor power (both in RIS and nqc), I expected the speed of the motor to be proportional to the power setting (i.e., higher power setting makes motor turn faster and vice versa). However, what I see is that the power setting appears to (...) (28 years ago, 17-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Robotics sub-groups
|
|
I would like to see at least one of these. It seems that there are several legOS-related projects ongoing and I'm sure people would like to avoid duplicating work (egcs-1.1.1 patches, libgcc.a, etc.). legOS is at the point in its development where (...) (28 years ago, 17-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Motor power?
|
|
=>From: Dan McCabe <danm@seanet.com> =>... =>When I set the motor power (both in RIS and nqc), I expected the speed =>of the motor to be proportional to the power setting (i.e., higher power =>setting makes motor turn faster and vice versa). (...) (28 years ago, 17-Feb-99, to lugnet.robotics)
|
| |
 | | Re: gleason research experiences?
|
|
Dear Mr. Puchol, Your order was shipped today via UPS Red, and you should have it tomorrow morning. Please be aware that our policy (as stated on our web site) is to ship orders the business day after they are received. Thank you, Wanda Gleason (...) (28 years ago, 17-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Using the Motor as a Tachometer
|
|
I don't know if someone else has already written about this, if so, sorry about being repetetive. I was reading about hooking up 2 motors A + B and arriving at a dynometer arrangement. ie. Turning A causes B to rotate. I tried this, but also hooked (...) (28 years ago, 17-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Motor power?
|
|
The firmware does do PWM. One reason you aren't seeing much difference is that the motor has an internal flywheel. When the pulse is "on", the motor revs up to speed, then this speed is maintained by the flywheel during the "off" pulse. If you put a (...) (28 years ago, 17-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Motor power?
|
|
I have a tracked bot and I can notice the difference in speed when I set the motors to 1 or 4 or 8. John A. Donaldson (...) (28 years ago, 16-Feb-99, to lugnet.robotics)
|
| |
 | | Re: RCX IR Messages & Universal Remotes
|
|
Ben, I've been trying to use my Palm III with OmniRemote to send messages to the RCX but so far with out success. What was the process you used to train your buttons? What I am doing is using nqc to send a message through the IR tower which I try (...) (28 years ago, 5-Feb-99, to lugnet.robotics)
|
| |
 | | Easy communication between HBs
|
|
After struggling with it for many hours I found an alternative to Randy's serialio.c serial communication which I couldn't get working. So I used the Pa7_9600 Baud Serial output from unknown origin (Fred?) ((URL) ial.html). I cut a standard RJ11 (...) (28 years ago, 17-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | A-S -> Adaptive Transmission (long)
|
|
My own incarnation of the much discussed A-S transmission uses a single differential and relies upon software to synchronize two independent drives. I term my gearing and software system an Adaptive Drive, since it continuously monitors differential (...) (28 years ago, 17-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Sonar and RF Modem questions
|
|
I've been looking into this also. I purchased the Parallax RF module, which is very simple to use. However, it seems to provide a transparent RS232 interface, more is needed than this, or at least some data buffering. Linx technologies provides a (...) (28 years ago, 17-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Recommended Add-On Sets?
|
|
Just a quick note: #8277 Giant Model Set ( or XXL) as someone called it also has four 14 SLU (standard LEGO unit) long beams. These are really useful once in a while. Also keep an eye out for 16 x 2 plates which are great for adding structural (...) (28 years ago, 16-Feb-99, to lugnet.robotics)
|
| |
 | | Re: RF VIDEO?
|
|
(...) I seem to recall seeing serveral kits that weren't too expensive, both online and at the neighborhood electronics parts store. This would commonly be used to transmit video from a single VCR or cable box to any TV in your house. Mike (28 years ago, 17-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Sonar and RF Modem questions
|
|
(...) Maybe a vender could get an eval kit, work through the interfacing issues and kit it for us to buy! That would probably stay within Lynx' licensing agreement and still provide a cost effective solution. Mike (28 years ago, 17-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | RE: gleason research experiences?
|
|
I bought my HB via email and had it at my door in three days. Its likely they got Valentines Day and Presidents Day off. I wish I did. . . shan (...) (28 years ago, 17-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Sonar and RF Modem questions
|
|
HB fans, A few questions for ya ... I just received my polaroid 6500 sonar module from wirz. Cool little gadget. I have the HB expansion board from gleason. Installation looks pretty straightforward with the expansion board, since the pins on the (...) (28 years ago, 17-Feb-99, to lugnet.robotics.handyboard)
|