 | | Re: Pneumatic 6 legged walker
|
|
(...) No, I'm sorry, I don't. It was just a quick sunday evening project, and I didn't even make a model which had a compressor built in. But it is rather easy to make one. First, you need to figure out how to make a suitable three phase feedback (...) (28 years ago, 4-Feb-99, to lugnet.robotics)
|
| |
 | | Re: what variety of 6811 can be used?
|
|
Nick, Sorry, I should have posted the link but I was out of the office yesterday and could not remember where it was. Motorola has an Engineering Bulletin call "Replacing 68HC11A Series MCUs with 68HC11E Series MCUs", it can be found at: (...) -- (...) (28 years ago, 4-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Memory erase or reset?
|
|
Hello, I have been loading an alternative runtime environment (not IC) onto the handy board to test it out, and I want to ensure that all of the RAM is erased before doing so. I can use the unload command in IC to delete all of the .c files, but how (...) (28 years ago, 4-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Pneumatic 6 legged walker
|
|
(...) unixers. Any chance that someone could undo this Intel compression? Regards, Johannes. (28 years ago, 4-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Pneumatic 6 legged walker
|
|
(...) It doesnt work with MoviePlayer on Mac either.. -- Kent -- Did you check the web site first?: (URL) (28 years ago, 4-Feb-99, to lugnet.robotics)
|
| |
 | | NVRAM
|
|
Hi! Here is Cesar Mello, from Brazil. I'd like to know if there is any NVRAM version of the 62256 chip, or any other solution smaller than the external batteries, or if it's possible to keep Interactive C and the user program loaded in an EPROM. (...) (28 years ago, 4-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Pneumatic 6 legged walker
|
|
(...) I once played with a Creative VideoBlaster and I've found out that many of the (useful) compression schemes the capture software installed were not available to the general public. I'm sure one of those was used and that's the problem. (...) (28 years ago, 4-Feb-99, to lugnet.robotics)
|
| |
 | | Re: R4 Resistor
|
|
where is this list that says 2.94K? please tell me so i can eradicate the incorrect value. to answer, yes, just use it, it affects the IR xmit frequency and nothing else. fred In your message you said: (...) (28 years ago, 4-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Alternative compilers for native RCX code?
|
|
A brief web search for "H8" and "compiler" showed up a number of people selling, er, H8/300 compilers. One notable entry was HI-TECH Software who have a limited eval compiler freely downloadable - see (URL) I haven't had time to go much further than (...) (28 years ago, 4-Feb-99, to lugnet.robotics)
|
| |
 | | Setting the Config Register
|
|
Greetings all! I just finished building the handyboard from a kit, and it seems to be working just fine except for the fact that I can't seem to get the config register to set to 0x0c. It is now working on the 0x0d setting, but I know this is (...) (28 years ago, 4-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Re: R4 Resistor
|
|
"Fred G. Martin" schrieb: (...) i have had the same problem, so i havent installed the ir-circuit yet. the mistake is in "The Handy Board Technical Reference" (July 12, 1998) PDF File ... On page 46 ( i am not sure) is a Part Listing: it says : .... (...) (28 years ago, 4-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Fw: 360 deg. swiveling electrical connection
|
|
Are you looking for a Lego pure solution? I have a though about some rotating metal disks that touch each other and are always in contact no matter what the rotation, but am not an EE, so I don't know if polarity would become an issue. trowt (...) (28 years ago, 4-Feb-99, to lugnet.robotics)
|
| |
 | | Re: R4 Resistor
|
|
thank you! yes, 3.83k is correct. fred In your message you said: (...) ile (...) (28 years ago, 4-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Memory erase or reset?
|
|
Either disconnect the batteries and all sources of power or remove the memory chip.... -phil (28 years ago, 4-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: NVRAM
|
|
Dallas Semiconductor makes some static RAMs with an internal battery. One of them is the DA1230AB/Y, a 256kbit (32Kbyte) battery backed static RAM. (URL) - - - Nick - - - (...) (28 years ago, 4-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: What is your current Mindstorm project?
|
|
(...) [ ... ] (...) This is exactly what I'm working on (as a long term goal). I only got my mindstorm a few days ago so I haven't gotten far. Currently I'm just trying to get my robot to survive in my flat for more than a minute! ;-) The main (...) (28 years ago, 4-Feb-99, to lugnet.robotics)
|
| |
 | | Unsubscribe
|
|
Thank's for the help !! Bye (28 years ago, 4-Feb-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Adder/Subtractor revisited
|
|
Well, I don't know about your experiences, but I have had tracked vehicles with identical (as much as possible) construction on each side of the vehicle that deviat several degrees for each foot travelled. This was due to the characteristics of the (...) (28 years ago, 4-Feb-99, to lugnet.robotics)
|
| |
 | | Re: 360 deg. swiveling electrical connection
|
|
Ben Kimball wrote in message ... (...) What about an axle with wires running along two of the groves (groves made by the cross section of the axle). You could have a two bands of thin metal sheeting wrapped around the axle. To each band you have on (...) (28 years ago, 4-Feb-99, to lugnet.robotics)
|
| |
 | | Re: Fw: 360 deg. swiveling electrical connection
|
|
I am an engineer with EE training. It would not be a problem if you use two concentric rings. One for the "live" voltage and one for a ground (or positive and negative if you prefer that notation). This is how many real world systems work. Matt R. (...) (28 years ago, 4-Feb-99, to lugnet.robotics)
|