To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *8296 (+20)
  Re: legOS
 
I dunno.. that's why I'm askin... -----Original Message----- From: Kekoa Proudfoot <kekoa@pixel.Stanford.EDU> To: lego-robotics@crynwr.com <lego-robotics@crynwr.com> Date: Friday, January 22, 1999 8:43 PM Subject: Re: legOS (...) up.. (...) -- Did (...) (28 years ago, 22-Jan-99, to lugnet.robotics)
 
  Re: Sensor monitoring
 
I'm new here and don't have much experience yet with the RCX, but I was just wondering... Is it possible to attach both sensors to a single input using one of the multi-input multiplexers (voltage divider arrangements) that I've read about on here? (...) (28 years ago, 22-Jan-99, to lugnet.robotics)
 
  Re: Sensor monitoring
 
(...) You can multiplex simple switchs that way, but not the light sensor. I requires power and outputs an analog value. (28 years ago, 22-Jan-99, to lugnet.robotics)
 
  (canceled)
 
 
  (canceled)
 
 
  (canceled)
 
 
  Re: is Mindstorm/RCX Y2K Compliant???
 
(...) microcontroller in the RCX does this, or not. Jasper (28 years ago, 22-Jan-99, to lugnet.robotics)
 
  navigation with compass
 
(...) Light sensor with a magnifier? :-) I tried using the differential gear to "remember" the initial heading of my robot, and painfully discovered that the result would drift off after many turns. Now I think compass is the way to go. (I wonder (...) (28 years ago, 22-Jan-99, to lugnet.robotics)
 
  MS on TV
 
Tonight (Tuesday november 10th) the Irish television programme "Tech TV" will be showing a short item on the lego MS. 10.20 AM RTE 2 enjoy dave. (28 years ago, 10-Nov-98, to lugnet.robotics)
 
  Re: CONTINUOUS BEEPING
 
I would suspect that the system locks up without the LCD. There is a PCODE out there for use without the LCD panel, and I believe that it is at the handyboard web site. K.L. McKinnon (...) (28 years ago, 22-Jan-99, to lugnet.robotics.handyboard)
 
  Re: Flexible axles!!!!
 
what exactly is znap? thanks! -- Chris Stanley cstanley@usit.net (...) (28 years ago, 22-Jan-99, to lugnet.robotics)
 
  Re: RCX 2.0 -- ideas.
 
(...) The big cost in these things, wqould be that you need 5 of the 2*2*2/3 plates at the end of Technic leads, unless you homebrew those too. AFAIK, you can only get leads, at least as far as Service packs are concerned, for about $5-$6 (with 2 (...) (28 years ago, 22-Jan-99, to lugnet.robotics)
 
  Re: expansion ports
 
(...) Reductio ad absurdam: You buy, say, 8880. You lose one of the, say, #12 axles. You replace with 2 #6 and an axle extender. You sell it on (bad move, IMHO, but hey, it could happen :) ). By your reasoning, you now have sold a product, not made (...) (28 years ago, 22-Jan-99, to lugnet.robotics)
 
  Re: Smooth Plates
 
(...) Set 6567 Speed Splasher has two red 1*8 tiles. It is available under $2.50, generally. But don't tell your SO, or you won't be able to buy a few multiples of 8277 :) (just bought two myself, over the last few days... I now have a _really_ (...) (28 years ago, 22-Jan-99, to lugnet.robotics)
 
  Re: Toy motors
 
I was reading the FAQ (again), and unless I overlooked something, it seems that even with the H-bridge or piggybacking solutions, I would not be able to drive a high-end R/C car engine (20+ amps)... So here are my questions: 1 - Could I lower the (...) (28 years ago, 22-Jan-99, to lugnet.robotics.handyboard)
 
  Re: Squishy Brick
 
(...) Is that the page where there is a 1*4 grey technic beam, pierced by a #3 or 4 axle, with a 16-tooth bevel (?) gearon one side, and a washer on the other? I think they put that picture in all Technic sets, to tell you that the axles have to be (...) (28 years ago, 23-Jan-99, to lugnet.robotics)
 
  Re: homebrew Temp sensor
 
(...) Hmm.. why no elco? that is, if you make sure you alway plug your sensor on in the same way, you should get a constant +ve and -ve... Mindstorms does use the standar measuring trick of having DC current run thru the resistor, right? Jasper (28 years ago, 23-Jan-99, to lugnet.robotics)
 
  Re: The Handyboard (was Re: RCX 2.0 -- ideas.)
 
(...) How about using a few large plates (of the type found as baseplates in small to medium sets), and a few basic bricks, possibly with the addition of glue to keep it all together? Jasper (28 years ago, 23-Jan-99, to lugnet.robotics)
 
  Re: expansion ports
 
Jasper Janssen wrote in message <36a90add.169456990@...et.com>... (...) Your examples are irrelevant because they probably don't still have active patents on the pieces and may or may not have ever had patents on all of them. What I was talking (...) (28 years ago, 23-Jan-99, to lugnet.robotics)
 
  NQC 1.1 b1
 
Due to feature creep, NQCC 1.0 never got out of beta. I've merged nqcc and the various utiltites (rcxfirm, rcxlog, etc) into a single program called nqc, and added some minor improvements to the compiler as well. The command line has changed quite a (...) (28 years ago, 23-Jan-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR