To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *8216 (+10)
  Re: Dacta in Canada?
 
Follow this thread back to the reference for Spectrum Canada. They sell to individuals as well as schools. (At least they sold to me last week and are shipping the merchandise to my home.) rob (...) (28 years ago, 21-Jan-99, to lugnet.robotics)
 
  Re: Help! Can't talk to IR Tower with Mac w/nqcc!
 
(...) That wiring looks fine, provided that "IR" is a DB-9 female that connects directly to the IR device. If you use the IR cable supplied by lego, then you'll need to swap pins 2 and 3. Mac pins 1 and 2 (RS-232 pins 7 and 8) are not required at (...) (28 years ago, 21-Jan-99, to lugnet.robotics)
 
  ROVER
 
Dear Mr Fred Martin/friends, We have run into some strange problems.Whenever we download the pcode_hb.s19 to the handy board using dl.exe we first get it is loading bootstrap program then the pcode.It shows the loading by a series of dots and (...) (28 years ago, 21-Jan-99, to lugnet.robotics.handyboard)
 
  Re: blowing analog inputs [was: Battery Level Indicator]
 
(...) this isn't right, so i feel the need to correct you. the hc11's analog inputs are sensitive; i have seen many of them destroyed (on a pin-by-pin basis), and voltages above 5v or below 0v are the cause). more accurately, it's not the voltage (...) (28 years ago, 21-Jan-99, to lugnet.robotics.handyboard)
 
  Re: Dual Coaxial power jacks?
 
good beginner questions... (...) you can use either. if you use the one on the interface, then power goes through the phone cable to charge the HB. if you use the one on the HB, then power goes through the phone cable to operate the ckts on the (...) (28 years ago, 21-Jan-99, to lugnet.robotics.handyboard)
 
  PVM output
 
Dear all, I looked at the lib_hb file and found the portion for motor outputs. void motor(int m, int speed) { if (speed>100) speed=100; if (speed<-100) speed=-100; if (speed >= 0) _set_motor(m, 0, (255*speed)/100); else _set_motor(m, 1, (...) (28 years ago, 21-Jan-99, to lugnet.robotics.handyboard)
 
  New comer to HB mailing list
 
Hello, everyone! I just joined to Handy Board mailing list and sincerely hope to exchange useful information and experience to enhance our daily joy with Handy Board. I am considering a kind of intelligent self recharging system of my robot. When (...) (28 years ago, 21-Jan-99, to lugnet.robotics.handyboard)
 
  Re: Direction of rotation sensor.
 
(...) Here's a thought: A rubber band around the axle to check and a pulley with a peg in it. In one direction, the pulley/peg run into the touch sensor and the band then starts slipping on the axle (hopefully geared down enough to sufficiently push (...) (28 years ago, 21-Jan-99, to lugnet.robotics)
 
  Re: Homebrew Rotation Sensor
 
I've added a circuit diagram for something that comes close to making voltages that look like a real LEGO Rotation Sensor. It's not perfect yet. The RCX may loose a few counts here and there. I think I need a better Opamp than the old LM324. (URL) (28 years ago, 21-Jan-99, to lugnet.robotics)
 
  Any interest in an RCX simulator?
 
I have been considering working on an RCX simulator for use with NQC programs. I'd be willing to develop the core simulator itself if others were willing to do the user interface work. I'll make sure the simulator is as portable as NQC currently is (...) (28 years ago, 21-Jan-99, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR