 | | Anyone implemented wall following behavior
|
|
Has anyone successfully implemented wall following behavior? If so, what kind of sensors or sensor tricks did you use to maintain a constant distance from the wall. Also do you have examples of nqc code that you would be willing to share? Your help (...) (28 years ago, 31-Dec-98, to lugnet.robotics)
|
| |
 | | Re: legOS - Does it work for you?
|
|
(...) If you change the BUTTON_RUN to BUTTON_PROGRAM in the speeds function it will work properly. Although there seems to be very little difference between a speed of 1 and a speed of 7. -rick (28 years ago, 31-Dec-98, to lugnet.robotics)
|
| |
 | | Re: voice recording and playback system
|
|
great website. Got a suggestion for you. Notice you are using the counter sink screws. Have looked at the brass #4 machine head screws? I am going to make some light sensors this weekend based on your design, for my project. I would think the (...) (28 years ago, 31-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Glueing blocks
|
|
I've successfully created mating surfaces by using a gel superglue. To create the mating surface, create a flat surface (if one doesn't exist) with epoxy. Then spread the gel glue on the suface, put down a piece of celophane wrap. Then press a lego (...) (28 years ago, 31-Dec-98, to lugnet.robotics)
|
| |
 | | Re: sensor input mux calculations
|
|
I've thought about this, but I've come up empty. If you could get between the input line and the 10K pull-up resistor, it would be easy. You could then wire the CdS cells on either side, with a 10K resistor from one cell to ground. Then when the (...) (28 years ago, 31-Dec-98, to lugnet.robotics)
|
| |
 | | Re: RCX 2.0 -- ideas.
|
|
The Version @.0 should have a way to allow multiply RCX's to used. That way one RCX could be used for just the motor routines, one to handle sensors, one to do number chrunching, and etc. John A. Donaldson (...) (28 years ago, 31-Dec-98, to lugnet.robotics)
|
| |
 | | Re: legOS - Does it work for you?
|
|
(...) Not necessarily - it may be that the replacement happens to put things were some memory corruption doesn't hit them... Cheers, Ben. (28 years ago, 31-Dec-98, to lugnet.robotics)
|
| |
 | | Re: legOS - Does it work for you?
|
|
I too have a similar problem. Using cygwin-b20 on a win98 machine to build the light-sensor demo under legOS 0.1.4 I downloaded the cross compiler from (URL) ( Gavin Smyth posted this address a few days ago.) With the light-sensor demo, the 12th (...) (28 years ago, 31-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Cybermaster Motor dead? Happend to anyone else?
|
|
Laurentino Martins schrieb in Nachricht (...) I know you said that fresh batteries didn't fixed it, but the only time it happened to me it happened *exactly* the way you said and the fix was to purchase new batteries. Sorry, but I have no other (...) (28 years ago, 31-Dec-98, to lugnet.robotics)
|
| |
 | | Re: RCX 2.0 -- ideas.
|
|
Laurentino Martins schrieb in Nachricht <4.1.19981231143643....90.220>... ..... cut something out, sorry Laurentino <g> (...) times per rotation using only two wires ??? (have I seen this wrong?) You have seen wrong, I disassembled my Unit because (...) (28 years ago, 31-Dec-98, to lugnet.robotics)
|