 | | Re: Sensor ideas
|
|
(...) I have thought of a simple level sensor that would use light sensors, a ring pipe, and a ball bearing. Drill holes through the ring, aligned like spokes. Place light sensors on the outside of the ring, facing in. Set the ring like a wheel, and (...) (28 years ago, 28-Dec-98, to lugnet.robotics)
|
| |
 | | BotCode
|
|
I am impressed with the amount of work done with RCX and alternate systems for coding and control. I suppose this is old news to most of you but BotCode is a very nice package for those that want to ditch the Lego interface. (URL) Clemens, Associate (...) (28 years ago, 28-Dec-98, to lugnet.robotics)
|
| |
 | | Mindstorms CD and Soft Windows
|
|
I have tried Virtual PC running Windows 95 on my G3 Mac and it doesn't quite work. The software itself runs (albeit with a bit of stuttering on the audio). The problem is the connection to the IR tower. The software doesn't recognize that the tower (...) (28 years ago, 28-Dec-98, to lugnet.robotics)
|
| |
 | | (no subject)
|
|
After reading Dave's commentary on the RCX's ADC system, I did a few more test's, and found that I could easily predict the value that the RCX would produce for a given resistor. Just use the voltage divider formula - V=R2 / (10,000 + R2) and (...) (28 years ago, 28-Dec-98, to lugnet.robotics)
|
| |
 | | More input
|
|
After realizing that the input ports read resistance, I had an idea. Suppose that I used a network of switches and parallel resisters to differentiate between switches? Here's the circuit I have in mind: gnd-----+--[22k]------ switch --+ A | | (...) (28 years ago, 28-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Voltage or resistance
|
|
I'm joining this thread a little late, so sorry if any of this has already been stated... For "passive" sensors, the RCX measures a voltage level, but since there's a pullup you may not get what you expect. If memory serves, the RCX ADC uses a 5.0V (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
|
| |
 | | The Bed Mill
|
|
I have posted some pictures of my latest mill at (URL) I will post a QuickTime movie when I complete the program and make a real cut. Bob (28 years ago, 27-Dec-98, to lugnet.robotics)
|
| |
 | | DC Motor Manufacturers
|
|
Hello everyone, Has anyone found a good source for DC motors? I am looking for small motors to use as direct drive movement of a small 1.5 LB robot. Any help is greatly appreciated! Bill Denzel Senior Mechatronics Student California Polytechnic (...) (28 years ago, 27-Dec-98, to lugnet.robotics.handyboard)
|
| |
 | | Voltage or resistance
|
|
After experimenting with various photo sensors, it appears that resistance is what is measured. Solar cells produce no change in readings, but CdS photo resisters do. I managed to hook up a BASIC STAMP (a small microcomputer by Parallax) to one of (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
|
| |
 | | Re: R/C Servo to Legos
|
|
I use epoxy to glue on assorted pieces where I need them. If you use enough epoxy to fill the space completely, you can snap off the piece and then you have a workable Lego bump impression. What I have found with epoxy is that the epoxy holds just (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Mindstorms CD and Soft Windows
|
|
(...) It seames to be not possible to use these emulators. I've tried them all and is doesn't work. Though the software will run, the hardware won't. There are two options: use Robolab from pitsco-dacta or use Not Quite C from Dave Baum (you can (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
|
| |
 | | Sensor ideas
|
|
Looking at some of the ideas for multiplexing touch sensors gave me a couple of ideas - I may not get around to constructing these anytime soon so if someone wants to run with them I'd sure like to hear how you did. Idea #1 - Whisker sensors using (...) (28 years ago, 26-Dec-98, to lugnet.robotics)
|
| |
 | | sensor details
|
|
Do the sensors read voltage or measure resistance? or both? chris (28 years ago, 27-Dec-98, to lugnet.robotics)
|
| |
 | | Re: R/C Servo to Legos
|
|
(...) something like a (...) The usual way the RC community does it is to use a cover from a auto tire valve stem, fill it with epoxy and push it over the splines of the output shaft. Be careful that no epoxy runs down into the bearing of shaft :-). (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
|
| |
 | | Re: Downloading problems
|
|
I haad similar problems and then I realized that I did not need to download pcode or anything special. I just ran IC and it connected -- all the ports are working fine... Scott Sherman (...) (28 years ago, 27-Dec-98, to lugnet.robotics.handyboard)
|
| |
 | | lego train and motors
|
|
Hi all. I received a cargo train for Christmas and was experimenting with the motors and speed control unit. I would like to incorporate the tracks and railway motor into some RCX projects in the near future. When I hook a regular lego motor (the (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
|
| |
 | | Re: R/C Servo to Legos
|
|
John Kittelsrud writes: > Does anyone have a solution for coupling the output of an R/C servo > to something like a Lego axel? I did it using an axle stopper glued on with hot-melt glue. Worked fine until I would over-torque it. (28 years ago, 27-Dec-98, to lugnet.robotics)
|
| |
 | | Re: R/C Servo to Legos
|
|
The srevo parts are Nylon, hard to glue on to that. I dont think gooping on epoxy would hold vary well, might be wrong. (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
|
| |
 | | Re: R/C Servo to Legos
|
|
You could glue a lego gear onto the servo horn and axles into that. (...) (28 years ago, 27-Dec-98, to lugnet.robotics)
|
| |
 | | R/C Servo to Legos
|
|
Does anyone have a solution for coupling the output of an R/C servo to something like a Lego axel? Thanks. (28 years ago, 27-Dec-98, to lugnet.robotics)
|