To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *6336 (-10)
  RE: Compass/directional sensor
 
I found a module at (URL) but it appears to only have serial output. The Dinsmore compass also seems to be referenced frequently ((URL) Kevin A. Saddi [SMTP:ksaddi@gte.net] Sent: Saturday, December 12, 1998 5:56 PM To: lego-robotics@crynwr.com (...) (28 years ago, 13-Dec-98, to lugnet.robotics)
 
  some kind of dividing circuit?!?!?!?!
 
hi, I am thinking of using motors with encoders built in them on my rugwarrior board, but the problem is that the motor returns 500 clicks per revolution. and since the counter can only hold about 32,000 the variable fills up and overflows very (...) (28 years ago, 13-Dec-98, to lugnet.robotics.handyboard)
 
  CM: Triple gait cycle hexapod
 
I've made a hexapod based on the Cybermaster mobile unit. There's no pictures available yet, but some LDraw diagrams. (URL) hope it is somewhat clear how it works. At least it shows that it is possible to make a model that isn't a car based on the (...) (28 years ago, 13-Dec-98, to lugnet.robotics)
 
  Re: Slope Parameter in SetSensorMode
 
(...) I wrote a simple VB program to look into this, and as far as I can tell ClearSensorValue does not reset the sensor state in this mode. It will remain in whatever state it was in until you turn the RCX off. You can even stop the program and (...) (28 years ago, 13-Dec-98, to lugnet.robotics)
 
  Re: Position Control Question ?
 
Thanks for your reply. To answer your question about position control, let me describe my application. I have an Handyboard, stepper motor, and a linear system (ball-screw), and I would like to control the position of the part mounted on the nut of (...) (28 years ago, 13-Dec-98, to lugnet.robotics.handyboard)
 
  Re: space shuttle technic set cost?
 
What was the name of the store?????? (...) (28 years ago, 13-Dec-98, to lugnet.robotics)
 
  RE: Slope Parameter in SetSensorMode
 
Good point, a ClearSensorValue seems to have fixed this. Thanks, David -----Original Message----- From: lugnet.robotics@lugnet.com [mailto:lugnet.robot...ugnet.com] Sent: 13 December 1998 13:47 To: lego-robotics@crynwr.com Subject: Re: Slope (...) (28 years ago, 13-Dec-98, to lugnet.robotics)
 
  Re: Slope Parameter in SetSensorMode
 
(...) has (...) sensor (...) The input would remain in whatever state it was in last. Depending on how much light it was seeing, when the flickering stopped it could be either on or off. (28 years ago, 13-Dec-98, to lugnet.robotics)
 
  Miniboard in space.
 
Hi, I realize that this is actually not a miniboard list, but since the miniboard is actually the handyboards little brother, I figured maybe this would be of interest. About a year ago I was asked to help a local high school integrate their (...) (28 years ago, 13-Dec-98, to lugnet.robotics.handyboard)
 
  RE: Slope Parameter in SetSensorMode
 
Hi, Yes, that's also how I understand the Slope Parameter. I have recently tried to use it for locating navigational beacons. The idea is this, I found that homing in on a simple constant light source was difficult unless the light source was much (...) (28 years ago, 13-Dec-98, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR