To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *5151 (+20)
  RE: Monitoring household power consumption
 
Actually, that little black band is a relic of earlier days when people (like myself) had jobs that occasionally required them to sit with a stopwatch and count turns. A slide rule was then used to calculate power consumption. Each meter had a (...) (28 years ago, 11-Nov-98, to lugnet.robotics.handyboard)
 
  Re: What about multiplexing sensors?
 
You can: 1. Put multiple Touch sensors on the same input but you can't tell which one was hit. 2. Put a Light and Touch sensor on the same input and read normal light levels except when the Touch is hit it the input will read 100. 3. There are a (...) (28 years ago, 11-Nov-98, to lugnet.robotics)
 
  Handy Board PLease!!
 
If Anyone is selling ther Handy Board Please Tell me!! I rreeeaaally neeeeed it for some Science Proj..! thank you! (28 years ago, 11-Nov-98, to lugnet.robotics.handyboard)
 
  RE: What about multiplexing sensors?
 
I'm thinking more along the lines of using all three outputs and all three inputs to code a multi (read "more than three of each input and/or output") I/O multiplexor? This inherently reduces the possible sample rate on each input or output (...) (28 years ago, 11-Nov-98, to lugnet.robotics)
 
  Re: What about multiplexing sensors?
 
(...) I've done it using an output port to control a MUX. I've been able to control up to three sensors through one input port. This could be extended to nine sensors through all three sensor ports. I'm working on ways to control more sensors both (...) (28 years ago, 11-Nov-98, to lugnet.robotics)
 
  Sensor inputs (more than three)
 
Has anyone noticed that each sensor input block has four connectors? If you connect one sensor to two connectors and another sensor to the other two, you essentially read both sensors simultaneously. If this could be munipulated somehow then you (...) (28 years ago, 11-Nov-98, to lugnet.robotics)
 
  Re: What about multiplexing sensors?
 
(...) I do. I only have two motors! 8^) But I'm looking at ways to use either the inputs to control the MUX or have an external control that the RCX can query to determine which sensor is currently active. ---Larry +---...---+ Larry Coffin (...) (28 years ago, 11-Nov-98, to lugnet.robotics)
 
  Re: What about multiplexing sensors?
 
(...) I guess I've lurked long enough...pardon my ignorance, but what's a MUX? --Andy (28 years ago, 11-Nov-98, to lugnet.robotics)
 
  RE: Monitoring household power consumption
 
I purchased a power meter from Brand electronics. They have a few different models. There is one that is suitable for measuring the costs of one device and there is a larger one that has to be hardwired into your house. Check out (URL) are pretty (...) (28 years ago, 11-Nov-98, to lugnet.robotics.handyboard)
 
  Re: What about multiplexing sensors?
 
MUX is short for multiplexer. Just a switch that lets you hook multiple things to one input. (...) (28 years ago, 11-Nov-98, to lugnet.robotics)
 
  Re: What about multiplexing sensors?
 
(...) MUX is short for 'multiplexer' -- it is essentially a multi-switch device that switches a single input (or output) to multiple outputs (inputs). It would allow you to have 8 sensors (for example) connected to one input port and you could (...) (28 years ago, 11-Nov-98, to lugnet.robotics)
 
  Re: What about multiplexing sensors?
 
Okay...thanks. --Andy (28 years ago, 11-Nov-98, to lugnet.robotics)
 
  Re: What about multiplexing sensors?
 
(...) Hang on - if you use all 3 outputs to control the MUX (which leaves me wondering why you'd bother - trees falling in forests and all that) you can get 24 inputs, even if you only treat each output as binary. More plausibly, you can use 2 (...) (28 years ago, 11-Nov-98, to lugnet.robotics)
 
  Re: RCX Programming Questions and Sensor Ideas
 
In article <199811102221.OAA071...ford.EDU>, Kekoa Proudfoot <kekoa@Graphics.Stanford.EDU> quotes and writes (...) You are right, of course. (...) If it does I haven't found it. (28 years ago, 11-Nov-98, to lugnet.robotics)
 
  RE: What about multiplexing sensors?
 
You should be able to have three or more on/off sensors share a single input port without multiplexing. Just use a different resistor for each, so that any combination of pressing the three sensors yields a unique value out of 8 possible. For (...) (28 years ago, 11-Nov-98, to lugnet.robotics)
 
  Re: What about multiplexing sensors?
 
(...) Sure, if you want to give up all three output ports -- which most people don't want to do. A no output RCX seems to have a pretty limited set of applications to me. At least with two output ports you can drive and steer a robot. I was using (...) (28 years ago, 11-Nov-98, to lugnet.robotics)
 
  RE: What about multiplexing sensors?
 
(...) This seems like what I call a statistical multiplexor or "StatMux". Seems like it may be more difficult to implement (ie ROM decoding, writing drivers, etc.), but the advantage of freeing up an output port is really cool. The hardware to (...) (28 years ago, 11-Nov-98, to lugnet.robotics)
 
  some interesting lego building
 
After reading the robot builder's guide on: (URL) had an idea... There's a really cool section about building strong structures with lego technics pieces, and they list the different possibilities for vertical braces that fit perfectly. The basic (...) (28 years ago, 11-Nov-98, to lugnet.robotics)
 
  RE: What about multiplexing sensors?
 
(...) One idea is to just use the input port itself to generate the clock signal under control of the RCX software. Otherwise, it is not too difficult to generate a clock using external hardware -- an IC and a few resitors and capacitors. But it (...) (28 years ago, 11-Nov-98, to lugnet.robotics)
 
  Re: some interesting lego building
 
In message <199811112132.NAA272...kimo.com>, Greg Alt <galt@eskimo.com> writes (...) Not with the CyberMaster design models on the CDRom! They go out of their way to attach flat thin cross strips everywhere to make the robot almost indestructable. (...) (28 years ago, 11-Nov-98, to lugnet.robotics)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR