 | | unsubscribe
|
|
unsubscribe (28 years ago, 18-Oct-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
(...) The small cylinders are of great use for actuators & orther small "switching" tasks... not good for lifting. (...) I have been disappointed in the "compressor" pump... It does not generate a very consistant presure, and it seems to have been (...) (28 years ago, 18-Oct-98, to lugnet.robotics, lugnet.build)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
(...) The small pump makes a fine compressor which lots of us use. I agree that the small cylinder is not that useful. The (...) Are you using a pressure limit switch to shut off the compressor? lu posted a design a while back which I captured on my (...) (28 years ago, 18-Oct-98, to lugnet.robotics, lugnet.build)
|
| |
 | | Re: new lego robotics mail alias
|
|
(...) That's true, it is, but some other discussions do come up (sensors, strategies for robot construction, etc.). I was one of those that didn't want to see the list MOVE here. Still don't, even with all the web interface improvements. But it (...) (28 years ago, 18-Oct-98, to lugnet.robotics)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
Larry, what happened to your sig.??? Larry Pieniazek wrote in message ... <snip> (...) Matt Marshall $%#$% Vacuum Cleaners Always get my pieces!!! Matt's Lego Page (URL) (28 years ago, 18-Oct-98, to lugnet.robotics, lugnet.build)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
Thanks for the pointers to your and Mike's sites! Big help..... Which motor (5114 or the newer 5225) has given you the best results? - - - Nick - - - (...) (28 years ago, 18-Oct-98, to lugnet.robotics, lugnet.build)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
The "offset axle" (there are two of them in the #5272 One Cylinder Motor ($3.25)) gives a ½ bump spacing ... just right for the larger pump. - - - Nick - - - (...) (28 years ago, 18-Oct-98, to lugnet.robotics, lugnet.build)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
(...) I'm posting via the web interface rather than via the netscape newsreader, so until Todd implements a cookie based sig, I have to type it in by hand (or paste it in from a file) I can't be bothered to set up a keyboard macro and I don't want (...) (28 years ago, 18-Oct-98, to lugnet.robotics, lugnet.build)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
(...) Mike's design is for the older (5114) motor. Since I had a bunch of those that Moz sent me, I never bothered trying to adapt the design to the newer one. Others may comment differently, but I have good results (the multiple air tank cylinders (...) (28 years ago, 18-Oct-98, to lugnet.robotics, lugnet.build)
|
| |
 | | Re: pneumatics & mindstorms?
|
|
(...) I'll soon post photos of the double pump I designed based on the single cylinder one on Mike?'s site. It has a smoother power stroke when the tank fills up. I still need to design a regulator though. The small cylinder is used as the bucket (...) (28 years ago, 18-Oct-98, to lugnet.robotics, lugnet.build)
|
| |
 | | Updates to MCC - VB Mindstorms application
|
|
I have posted updates to the latest version of MCC (Mindstorms Control Centre) V 0.2.1 Fixed minor issues related to visual representation of motor controls. See LEGO -> CODE section for downloads of the exe and VB 5 project files. -- Visit my (...) (28 years ago, 18-Oct-98, to lugnet.robotics)
|
| |
 | | Address locations port d and y0
|
|
Ok I've had another read of the FAQ, as well as a close look at the schematics for the handyboard and the expansion board. Correct me if I'm wrong, but I think I can use d0-d7 along with Y0 or similar and hook these into a HC374 to get some digital (...) (28 years ago, 18-Oct-98, to lugnet.robotics.handyboard)
|
| |
 | | NEC V40
|
|
Sorry to intrude, I would like to check with people of this list if any one have used the NEC V40 ucontroller before. I'm doing a project on this and have problem programming the timer and intrl3. Kind reply to me personally at (...) (28 years ago, 18-Oct-98, to lugnet.robotics.handyboard)
|
| |
 | | Re: Address locations port d and y0
|
|
it's in the faq, at (URL) you do is write to 0x4000, 0x5000, 0x6000 depending on whether your latch is attached to Y0, Y2, or Y4 (respectively). e.g., "poke(0x4000, 0xff);" will set all the bits of a latch attached to Y0 to 1. Fred In your message (...) (28 years ago, 18-Oct-98, to lugnet.robotics.handyboard)
|
| |
 | | Rocker-boogie suspension model
|
|
Here is a model that incorporates a 6 wheel drive, independent and un-sprung suspension system. This was modeled after the rocker-boogie suspension on Sojourner. As I mention below, this is quick to build and real fun to watch climb across your Lego (...) (28 years ago, 18-Oct-98, to lugnet.build, lugnet.robotics)
|
| |
 | | Re: Rocker-boogie suspension model
|
|
(...) office, I think... Can you describe how to set up the motors? It's not clear in the picture, and I don't want to have to dig up LDraw to figure it out. Thanks, -Kekoa (28 years ago, 18-Oct-98, to lugnet.build, lugnet.robotics)
|
| |
 | | platform choices...
|
|
Hi: When I was in school, we built an autonomous mobile robot based on a six wheeled, 'electric ride-on toy' from Toys-R-Us. It had a sturdy metal frame, two nicely geared motors, a decent battery. It worked fairly well and could carry a large (...) (28 years ago, 19-Oct-98, to lugnet.robotics.handyboard)
|
| |
 | | (canceled)
|
|
|
| |
 | | Re: Charging batteries
|
|
(...) There are also Renewal rechargeable Alkaline batteries from Rayovac. They have a special charger that shuts off so they aren't over charged. Cindy Salwen (28 years ago, 19-Oct-98, to lugnet.robotics)
|
| |
 | | Re: waterproof seals (a bit OT)
|
|
(...) A little off the wall, but would it simplify the sealing if you could pressurize the inside to something close to the pressure outside (equalize pressures). A miniature CO2 cartridge with a release valve may help. Mike (28 years ago, 19-Oct-98, to lugnet.robotics.handyboard)
|