To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *44529 (-20)
  Re: Request for info on the Control Lab Interface.
 
(...) Yes, programs are executed on the PC. (...) Nothing is stored on the device. (...) It resides on the PC. (...) AFAIK, you will need a newer version of ROBOLAB. The older versions (forget which) did not support ControlLab. If you're up to the (...) (21 years ago, 11-Apr-06, to lugnet.robotics, lugnet.technic, FTX)
 
  Re: Help with converting voltage on circuit board
 
(...) Hi Danny, If we supply +12V to the top of the transistors, the drive circuit will most likely not be able to block those transistors completely (unless said drive circuit has an open collector structure with a pull up to the emitter of the (...) (21 years ago, 11-Apr-06, to lugnet.robotics, lugnet.technic)
 
  Re: Request for info on the Control Lab Interface.
 
Just today I got one of these from an eBay auction, including the original cable in a sealed plastic bag. The ROBOLAB software wasn't included, however, so I imagine that I'll need a driver of some kind to use it. Does anyone have a driver? (This (...) (21 years ago, 11-Apr-06, to lugnet.robotics, lugnet.technic, FTX)
 
  TexLUG Austin robotic line-following contest 6/11/06
 
Folks, The Austin chapter of the Texas Lego Users Group (TexLUG) is holding a robotic line following contest on June 11, 2006. In this line following contest, robots attempt to complete a specified race course by following a black line on a white (...) (21 years ago, 11-Apr-06, to lugnet.org.us.texlug, lugnet.loc.us.tx.aus, lugnet.loc.us.tx, lugnet.robotics)
 
  Re: Help with converting voltage on circuit board
 
(...) Thanks Dustin, those will help. I am inclined to agree with Philippe Hurbaine on the regulator. It is also obvious that it can take AC from the full wave rectifier near the power port. In answer to Davids question about the 4v connector (using (...) (21 years ago, 8-Apr-06, to lugnet.robotics, lugnet.technic)
 
  Re: Will NXT will work on Intel Macs ???
 
Hi, given that Intel Macs come with Rosetta as the legacy compatibility layer, even if LEGO doesn't ship NXT with universal binaries, the SW should run on the Intel Macs with reasonable performance. I'm quite curious about NXT actually since it took (...) (21 years ago, 8-Apr-06, to lugnet.robotics.rcx)
 
  Re: Help with converting voltage on circuit board
 
(...) The BDX34 transistor + toroidal inductor above + LM339 comparator probably compose a switching regulator efficiently converting 13V input power to 4.5V for the outputs. Philo (21 years ago, 8-Apr-06, to lugnet.robotics, lugnet.technic)
 
  Re: Help with converting voltage on circuit board
 
I've taken some more detailed pictures of the circuit and the reverse side. (URL) through the manual, connections 6 and 7 are for sensors and connections 0-5 are for output (4V as labled on the cover), but you only can turn the circuit on or off. (...) (21 years ago, 8-Apr-06, to lugnet.robotics, lugnet.technic)
 
  Re: Help with converting voltage on circuit board
 
(...) Hi Dustin, I am an EE. Before I give you some advice, I need a bit more information about 9750 (I have never seen one in person): - I see a power jack: I assume this powers the electronic circuit, not the loads, right? What voltage is applied (...) (21 years ago, 8-Apr-06, to lugnet.robotics, lugnet.technic)
 
  Re: Will NXT will work on Intel Macs ???
 
(...) The system requirements at lego.com say it requires MacOS X v. 10.3.9 or 10.4 and I'm pretty sure that runs on Intel Macs? So I'm guessing yes. But you could always contact LEGO customer support and ask. They might be able to help. ROSCO (21 years ago, 8-Apr-06, to lugnet.robotics.rcx)
 
  Re: Help with converting voltage on circuit board
 
(...) Wow - I remember those, we used them at school. Now why is it that Peeron do not have an entry for it under 9750? Those are also some big old capacitors, I would be inclined to check out their ESR (a rating of their health if you like) before (...) (21 years ago, 8-Apr-06, to lugnet.robotics, lugnet.technic)
 
  Will NXT will work on Intel Macs ???
 
All is in the subject... Thanks, - Christophe - (21 years ago, 8-Apr-06, to lugnet.robotics.rcx)
 
  Re: Help with converting voltage on circuit board
 
(...) I am not an EE either but I can see at least 2 things that look like voltage regulators. (21 years ago, 7-Apr-06, to lugnet.robotics, lugnet.technic)
 
  Help with converting voltage on circuit board
 
I'd like to try to convert the output of the voltage on a 9750 from 4V to 12V (to control 12V trains :). I've taken a photo of the internal circuit board - my rudimentary EE knowledge leads me to be believe I need to swap out the transistors that (...) (21 years ago, 7-Apr-06, to lugnet.robotics, lugnet.technic)
 
  LEGO Engineer Software
 
Does anyone have a copy of or know of a good link to download the LEGO Engineer software - all the links that point to NASA sites don't seem to be valid anymore. Dustin (21 years ago, 7-Apr-06, to lugnet.robotics)
 
  Re: RCX & RIS, a fading glory?
 
(...) Well, golly! some of this is coming true. (^_^) (albeit three years later) I for one am mighty happy about the rechargable battery in the Education version of the NXT!!! Sounds like it might even have direct power options. -Suz (who really (...) (21 years ago, 7-Apr-06, to lugnet.robotics.rcx)
 
  Re: Does my RCX work?
 
(...) Hi Marc, After you put batteries in, press the on/off button, it should beep twice and show a little man beside the number 1. If you don't get that, you have problems they may be fixable, but you probably want to seek help from someone (...) (21 years ago, 7-Apr-06, to lugnet.robotics.rcx, FTX)
 
  Re: Does my RCX work?
 
(...) First, put batteries in it and turn it on. It'll beep 'ok'. Then attach a technic 9v motor to port A with a wire and press Run. If the motor spins, the brick has basic sanity, and it's worth your time and money to get a IR tower to program it (...) (21 years ago, 7-Apr-06, to lugnet.robotics.rcx, FTX)
 
  Does my RCX work?
 
Hello all. I know almost nothing about LEGO robotics, but my mom picked up an RCX 1.0 brick at a yard sale. I just have the brick - no accessories, no software. Before I go buying stuff to go with it, is there any way to tell if this thing even (...) (21 years ago, 7-Apr-06, to lugnet.robotics.rcx, FTX)
 
  Re: rebeco
 
I have to say I really like the ideas in this. Having seen Jason Railton's automation recently and having been considereing technic solutions for train things any overlap of the two is good in my book. Just one thing tho, the video of the (...) (21 years ago, 6-Apr-06, to lugnet.trains, lugnet.robotics.rcx)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR