 | | Lindows
|
|
since it is based on linux, BrickOS should work on it, right? Timothy (23 years ago, 3-Dec-02, to lugnet.robotics.rcx.legos)
|
| |
| | searching for an Invention Kit for sale.
|
|
Hi everyone! I live in Hungary and it's quite hard to find a used invention kit (the new one is too expensive for me). So if someone has a kit for sale or just parts of a kit (I need especially motors, sensors (min. two), one light sensor, infrared (...) (23 years ago, 3-Dec-02, to lugnet.robotics)
|
| |
| | 68HC11A1FN
|
|
Dear all, I'm looking for the library for drawing a modified schematic for the HandBoard, but Protel does not have the library for this. Does anybody have? or is there any other chip which could replace the current one?? Thanks Rita (23 years ago, 3-Dec-02, to lugnet.robotics.handyboard)
|
| |
| | RE: RCX Tank Base
|
|
<SNIP> (...) I realized a few minutes after making my post that there is LEGO string. It is of suitable size. And, based on creations I've seen from the AFOLs, it's definitely strong enough. - Rob (23 years ago, 3-Dec-02, to lugnet.robotics)
|
| |
| | RE: Using TIS and USB Tower on a Macintosh
|
|
Hello, According to what I've read, Robolab 1.5 will work with the USB tower on a Mac. This leads me to believe that the Robolab CD comes with USB drivers for the tower. Emulators (as I understand them) work by mapping working resources to an (...) (23 years ago, 3-Dec-02, to lugnet.robotics)
|
| |
| | Re: Line following algorithms
|
|
From: Gary Mullen <garym@the-mullens.net> (...) It's a little of both. (prize & prestige) When you go to a contest sponsored by a robot club, they often give out "real robot" prizes. (stuff WE can't usually use) But at the last line following event (...) (23 years ago, 3-Dec-02, to lugnet.robotics)
|
| |
| | Re: RCX Tank Base
|
|
(...) > of trying hot-glue if it doesn't melt the LEGO's... There are two kinds of hot-melt glue guns - High temperature and Low temperature. I know that the low temperature kind definitely don't melt Lego and the glue does peel off relatively (...) (23 years ago, 3-Dec-02, to lugnet.robotics)
|
| |
| | Re: RCX Tank Base
|
|
(...) Depends on who you are, a 100% LEGO solution is better IMHO. Of course glue or cross stitching falls out of the purists world. I once made some heavy duty treads from halvbeams and cross axles but found it difficult to get enough traction from (...) (23 years ago, 3-Dec-02, to lugnet.robotics)
|
| |
| | Re: RCX Tank Base
|
|
Are non-Lego treads are out of the question? I've had lots of luck with different brands including the ones shown on my very old web page at www.borg.com/~pinkmice JB (...) (23 years ago, 3-Dec-02, to lugnet.robotics)
|
| |
| | RE: RCX Tank Base
|
|
<SNIP> (...) I haven't tried any adhesives on my tracks yet, but I was thinking of trying hot-glue if it doesn't melt the LEGO's or some tub caulk. School glue and/or wood glue (leaning more towards wood glue) may have enough strength to hold and it (...) (23 years ago, 3-Dec-02, to lugnet.robotics)
|
| |
| | Re: Line following algorithms
|
|
(...) I don't think there is really a good source for this information, yet. I'm planning on making a web page with information about line following, including event locations, in the near future. One place to look is the regular robot clubs. Like: (...) (23 years ago, 3-Dec-02, to lugnet.robotics)
|
| |
| | Re: hovercraft in motion
|
|
(URL) (23 years ago, 3-Dec-02, to lugnet.robotics)
|
| |
| | Re: hovercraft in motion
|
|
hi stef mientki gives the ability to see my hovercraft in motion thanx stef (URL) file soon (i hope today) depends on stef's free time :)) regards pixel (23 years ago, 3-Dec-02, to lugnet.robotics)
|
| |
| | Re: Another cement mixer......
|
|
(...) Hi Tobbe, sorry for delay in replying you, I have pleasure in your comment. As you specified, main news on this model are RCX's applications. Really my target is building a big "work zone" technic figure scale with 3-4 interactive models (...) (23 years ago, 3-Dec-02, to lugnet.technic, lugnet.robotics, lugnet.general, lugnet.modelteam, lugnet.loc.it)
|
| |
| | Re: RCX Tank Base
|
|
(...) Yeah, tell me about it. My latest MOC (still to be published) uses 1 x 6 plates on this type of treads and I made the MOC remote controlled and had to pick up a lot of plates when I was done driving. The treads have some serious flaws but are (...) (23 years ago, 3-Dec-02, to lugnet.robotics, lugnet.technic)
|
| |
| | Re: hovercraft
|
|
hi all again mission 1.5 completed it means i did big brother of my hovercraft so this is some data diameter of deck: 53 cm skirt length: 6 cm diameter of duct (tunnel): 15 cm height of tunnel: 8 cm i used lighter (thiner) film lighter scotch the (...) (23 years ago, 3-Dec-02, to lugnet.robotics)
|
| |
| | Re: hovercraft
|
|
at last :)))) hi stef i'm interrested in sending you my movies converted to mpeg files if you are ready let me know i can sent movies sliced on about 2mb pieces i'm ready to send thanx a lot regards pixel (23 years ago, 3-Dec-02, to lugnet.technic, lugnet.robotics)
|
| |
| | Re: Line following algorithms
|
|
(...) Of course. But then, some are more "real" than others ;-) (23 years ago, 3-Dec-02, to lugnet.robotics)
|
| |
| | Re: RCX Tank Base
|
|
Should have posted this hear Peter, (...) Alas, unfortunately I consider myself to be somewhat of a Lego purist, I look for almost pure Lego solution where I don't have to 'modify' bricks. If I started buying non-Lego stuff I'm afraid my hobby might (...) (23 years ago, 3-Dec-02, to lugnet.robotics, lugnet.technic)
|
| |
| | Re: RCX Tank Base
|
|
(...) When I was first designing the tank base I had assumed I would have to use an adder/subtractor to have straight driving. I spent a fair put of time playing with different A/S trying to fugure out which would be best to use. It was then that I (...) (23 years ago, 3-Dec-02, to lugnet.robotics, lugnet.technic)
|
