 | | Re: Brainstorms
|
|
OK, I've been watching this thread for a few days (I am LUCNY's "Expert Lurker" after all !) and refining some ideas that I've had for a while in hopes that I can contibute to this dicussion in a useful way. Please keep in mind that I'm a Mechanical (...) (24 years ago, 11-Aug-02, to lugnet.robotics)
|
| |
 | | About lejos 2.0!
|
|
Hi! Does lejos 2.0 need Java Comm. API? Laurence (24 years ago, 11-Aug-02, to lugnet.robotics.rcx.robolab)
|
| |
 | | Re: Brainstorms
|
|
(...) <snipped some reasonable arguments> This is why I recommend that 'brainstorms' goes with something like I2C. That protocol is fast and built into the chip. No software serial I/O is ever needed and every chip already speaks the protocol so (...) (24 years ago, 11-Aug-02, to lugnet.robotics)
|
| |
 | | Re: Brainstorms
|
|
Steve: Everything is a compromise. Here is a discussion of the issues that caused us to pick 2400 baud for RoboBricks: 1) Most of the various PIC's that we use (PIC12C509A, PIC12C672, PIC16C505) run at 4MHz. The 4MHz clock rate is divided by 4 to (...) (24 years ago, 11-Aug-02, to lugnet.robotics)
|
| |
 | | Re: Spybotics vs Cricket
|
|
Paul Andrews writes: > In lugnet.robotics, Russell Nelson <nelson@crynwr.com> writes: > *Mad* props to anybody who > >makes a loop network (ala the Clarkson Loop from my Master's thesis) > >out of three or more spybots. > > Err. What's a Clarkson (...) (24 years ago, 11-Aug-02, to lugnet.robotics)
|
| |
 | | RE: Programming multiple controllers
|
|
(...) OK, I'll bite, how does the Spybot get into this state? We've already discussed how to set up a secure link - how do we set up a non-secure link? Cheers, Ralph (24 years ago, 10-Aug-02, to lugnet.robotics.spybotics)
|
| |
 | | Re: Programming multiple controllers
|
|
(...) got (...) configuration? Bot one must be on Accept commands from ALL channels Mode. Dean (24 years ago, 10-Aug-02, to lugnet.robotics.spybotics)
|
| |
 | | Win98 install help
|
|
Hi there. Please can someone help me. I've been following the instructions at: (URL) word for word and then I got to the bit where it says: "Last setup I've tried let you choose which modules you need to download and setup. Here is a minimal list (...) (24 years ago, 10-Aug-02, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: measuring motor voltage on sensor input
|
|
Quoting Paul Andrews <paul@jools.net>: (...) How about a simple resistive divider across the motor output, say two 1 Kohm resistors, with the motor on the top of the two and the sensor input on the midpoint, so it sees the battery divided by two? (...) (24 years ago, 10-Aug-02, to lugnet.robotics)
|
| |
 | | RE: Brainstorms
|
|
(...) <just an opinion> The 2400 baud rate was probably chosen as a compromise between speed and what could reasonably be done on the teeny leetle PIC processor that drive the bricks. In practice, with the dedicated protocol that Wayne describes, (...) (24 years ago, 10-Aug-02, to lugnet.robotics)
|
| |
 | | Re: Brainstorms
|
|
(...) the interconnect protocol is run so slowly. Why only 2400 baud? Anything where you have an actual copper wire connection could run orders of magnitude faster. Heck even iRDA goes faster over infraRed. ---...--- Steve Baker ---...--- Mail : (...) (24 years ago, 10-Aug-02, to lugnet.robotics)
|
| |
 | | RE: Brainstorms
|
|
Wayne, In the spec you indicate that each brick gets its own 128 bit random number. This is like a serial number that is initially use to uniquely identify each brick with a shorter BrickID. This is a common technique in fire alarm systems where (...) (24 years ago, 10-Aug-02, to lugnet.robotics)
|
| |
 | | RE: Brainstorms
|
|
Wayne wrote (in his first post no less!) (...) <snip> (...) <snip> This is more like it. I've snipped out the juicy bits on the serial comms channel and modular power connector. The comms channel sounds a bit slow, but then again the fire alarm (...) (24 years ago, 10-Aug-02, to lugnet.robotics)
|
| |
 | | Re: Brainstorms
|
|
All: I think the project that I am working, called RoboBricks, on is quite relevant to this topic. Since this is my first post to this group, I should introduce myself as a very active member of the Home Brew Robitics Club based out of San Jose, (...) (24 years ago, 10-Aug-02, to lugnet.robotics)
|
| |
 | | Re: LEGO Purism
|
|
There are good, rational reasons for most of these decisions: (...) That makes good sense - because once a piece has been modified, you can't use it for it's intended purpose again. (...) That also makes sense - because it's purely decorative - and (...) (24 years ago, 10-Aug-02, to lugnet.robotics)
|
| |
 | | Re: LEGO Purism
|
|
(...) That's nice... what is the underlying issue? Is it not being true to Lego form? I think the overall concept of being Lego Purity is a personal decision. What levels you are willing to go may be different to what the guy down the road, etc. If (...) (24 years ago, 10-Aug-02, to lugnet.robotics)
|
| |
 | | Re: LEGO Purism
|
|
(...) I don't suppose you have some code for this do you? I tried this some while back with no success :-(. I found that the battery voltage seemed to fluctuate too much for me to be able to detect a stall condition with any degree of certainty. (...) (24 years ago, 10-Aug-02, to lugnet.robotics)
|
| |
 | | Re: LEGO Purism
|
|
(...) A little experimentation shows that you are right :-) or should that be :-( (24 years ago, 10-Aug-02, to lugnet.robotics)
|
| |
 | | RE: Brainstorms (battery options)
|
|
(...) I like the 9.6V NiMH R/C model battery packs, that's what we use in my university class. It's easy to parallel them or have separate packs for brain, motor and servos. Should we stick with that and add an on-board charger? Or keep the charger (...) (24 years ago, 9-Aug-02, to lugnet.robotics)
|
| |
 | | RE: Brainstorms - multiple I/O buses
|
|
(...) Exactly our approach. JStik on a JCX system will have ethernet, high speed I/O bus (bytewide data, addresses and strobes). SPI and I2C are supported, also Dallas 1Wire with a JSimm board plug in. Oh, IrDA and RS485 will be options too. When? (...) (24 years ago, 9-Aug-02, to lugnet.robotics)
|