To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *2936 (+10)
  UK SUPPLIERS OF PCBS
 
Bill, BB> Does anyone know of UK suppliers for Handy Board PCBs and/or BB> component kits. I looked around a bit for a UK supplier too and found.. well, zip, nothing. So eventually I ordered a Handyboard PCB from Douglas Electronics in California. (...) (29 years ago, 6-Nov-97, to lugnet.robotics.handyboard)
 
  Re: Shaft Encoders
 
On Wed, 5 Nov 1997, David W. Kammer wrote: We are interested in connecting two shaft encoders to the wheels of our (...) You did not give specifications! Degrees/pulse (optical) or degrees/volt (resistor or LVDT), Speed maximum, Shaft size, and etc. (...) (29 years ago, 6-Nov-97, to lugnet.robotics.handyboard)
 
  Re: Shaft Encoders
 
Has anyone used an comercial optical encoder to monitor wheel velocity on their robot? Most of the ones i have seen use between 100 and 500 pulses/rev. This is a lot for the little software driven encoder routines to keep up with. I was just (...) (29 years ago, 6-Nov-97, to lugnet.robotics.handyboard)
 
  Procedure to get off mailing list?
 
Hi all, I was wondering how do I get off this mailing list? Thanks..... ===...=== Dale Bergman P.Eng Systems Engineer T Telehealth Solutions Computing Devices Canada. 1020 68th Ave N.E. Calgary, Alberta, Canada. T2E 8P2 Voice: (403)295-6778 Fax: (...) (29 years ago, 7-Nov-97, to lugnet.robotics.handyboard)
 
  Re: Help in Assembler
 
What is "ORG"? Does it matter what number you use? Is the number a memory location? Thanks for any help! :) ---...--- ericson mar Master of Engineering Candidate Project: Mobile Robotics mar@cooper.edu (212)353-4356 Department of Mechanical (...) (29 years ago, 7-Nov-97, to lugnet.robotics.handyboard)
 
  IR devices
 
I recently opened up a mouse (the computer kind, not the live kind) and found what I assume to be 2 IR shaft encoders which it uses to translate the direction you are moving the mouse. Is there a way that I could remove them and turn them into shaft (...) (29 years ago, 7-Nov-97, to lugnet.robotics.handyboard)
 
  Re: Shaft Encoders
 
(...) We used the line of "S1" optical encoders from US Digital Corp. ((URL) and found them to work superbly. The encoders are light (~.07 lb) and small (~1.7" x 1.3"). The company is a "Value Added Retailer" and adds housings/bearings/whathaveyou (...) (29 years ago, 8-Nov-97, to lugnet.robotics.handyboard)
 
  Burning hot motor driver chips.
 
After not doing anything with my HB for a few months, I decided to buy a cheap RC car and use it as a platform. Anyway, I get a car that takes 6 AA batteries because I figure that the main motor is probably 9v (maybe that was a faulty assumption). (...) (29 years ago, 9-Nov-97, to lugnet.robotics.handyboard)
 
  Re: Burning hot motor driver chips.
 
Anthony, (...) Yes it sounds like it. (...) It does. The L293D still works after it cools off, doesn't it? (...) I suspect you are going to need more than just two piggy backed L293D. (...) You might have a look at Ben Wirz website, he sells various (...) (29 years ago, 9-Nov-97, to lugnet.robotics.handyboard)
 
  Re: Burning hot motor driver chips.
 
(...) sounds reasonable.. which "car" BTW? Some may be using that very same platform and may have some timely advice for you. (...) sounds like overload/overheating cutoff to me. (...) This is from the Handy Board FAQ : <---snip---> It is possible (...) (29 years ago, 9-Nov-97, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR