 | | Re: HB and ICC11..
|
|
(...) The trick is to copy the mode-change/LCD code into the on-chip RAM and execute it from there. This code must change to single-chip mode, write to the LCD, then change back to expanded mode. When in single-chip mode, you lose access to any (...) (29 years ago, 2-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: HB and ICC11..
|
|
Howdy- I saw your posting on the HandyBoard list. I don't know if I have any LCD code laying about or not but I'll look and see. Meanwhile, I noticed in your letter that you indicated you were using ImageCraft-C with the HandyBoard. I was wondering (...) (29 years ago, 2-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: HB and ICC11..
|
|
please post any answers to the board, as I also have ImageCraft's C compiler and have been as yet unable to set it up properly. thanks, -patrick (...) HandyBoard. (...) your (...) using (...) (29 years ago, 3-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Trouble shooting 7.2.2 (The digital inputs)
|
|
you are using the wrong library file. configure IC to use lib_hb.c, not lib_r22.c. -fred In your message you said: (...) (29 years ago, 3-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Trouble shooting 7.2.2 (The digital inputs)
|
|
(...) Thanks, that fixed the problem. I am happy to find that the problem was just software. Anthony Oren Loeppert *** (URL) * o* * ***> * * * * * | | * * | / * * |/ * * * * * * **\ (29 years ago, 3-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | lcd and ds1233-10 supplier
|
|
Just for the record, I was able to get the Hitachi LCD and the Dallas Semi. voltage monitor from Sterling Electronics. Their number is (512)836-1341. This location is in Austin, TX, but I think that they have a 1800 number, though I don't know it. (...) (29 years ago, 3-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Future versions of handyboard?
|
|
(...) I suspect there probably aren't such plans. One of the problems is the amount of infra-structure needed for a successful board. Basically you need a good board and a good development environment, and you have to be as inexpensive as possible (...) (29 years ago, 3-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Svar: Trouble shooting 7.2.2 (The digital inputs)
|
|
Hej I'm had the same problem, until i found that I loaded some programs via lib-file, not suitably for HB. (lib_r22.c) It seems you are running some programs for the 6.270. Have You setup IC correct? Try run c:\IC -config. Check out your lib-files. (...) (29 years ago, 3-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: voice synthesis
|
|
(...) Wow, impressive board. However, it's a bit out of my price range - I was hoping for a solution just about as cheap as the Radio Shack one used to be. Quality of speech isn't that much of a factor, I'm merely going to try and put this thing on (...) (29 years ago, 3-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Chip Puller
|
|
Does anyone know where I can buy a chip puller for the 6811. Robin (29 years ago, 3-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Chip Puller
|
|
R> Does anyone know where I can buy a chip puller for the 6811. R> Robin Jameco sells 'em ((URL) Part no 16766 $3.95 If you are careful, and stuff, you can use little screwdrivers to pull chips. Wiggle one corner loose, then the other, then the (...) (29 years ago, 3-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Chip Puller
|
|
(...) This is good advice! Their sales number is: (800) 831-4242. I think I saw a similar device in Radio Shack the last time I was there as well. I don't know what the price was but probably comparable. (...) This is NOT good advice! :) It is my (...) (29 years ago, 3-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: voice synthesis
|
|
There used to be a company that made a vowel synthesis kit, but I think they pulled it. Some science catalog company still had a bunch, back in January, and I have one (oh joy of joys). I may still have a scanned image of the schematics from it that (...) (29 years ago, 3-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Backlit screen and external power
|
|
Hi, 1.Does anyone know of a backlit and/or larger compatible LCD screen? 2.Are the problems with using a larger power supply than 500ma related only to battery overcharging and in this case can the battery be replaced with a larger amperage power (...) (29 years ago, 4-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Auton. underwater vehicles
|
|
Most robot builders work on mobile and walker robots. A few developers, however, have addressed another challenge: autonomous underwater vehicles. This research requires new sensors and special concern to mechanical details. With one major mistake, (...) (29 years ago, 4-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: voice synthesis
|
|
Jeff, JDR Microdevices sells the General Insturments CTS256AL2 chip (GI8642CAA) for ** $4.95 **. This is (I think) a slightly newer version of the same chip that Radio Shack used to sell. I bought one of those with an order from JDR, but haven't had (...) (29 years ago, 5-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Re: Backlit screen and external power
|
|
(...) Hi there Joe- (...) Yes, you're gonna like this- just about any "Optrex-compatible" LCD display can be used on the HandyBoard. There are two caveats however, most of these displays have a 14-pin header connection and not the 14-pin inline (...) (29 years ago, 5-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Unsubscribe
|
|
Unsubscribe Me Please! (29 years ago, 5-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | vector 2 x sample programs
|
|
Hello Everyone: I have just finished hooking up my vector2x compass and it seems to work fine thanks to Tom Brusehaver's good work and instructions.The only goof I made was to reverse the input and output lines. After about two hours of inspection (...) (29 years ago, 5-Jul-97, to lugnet.robotics.handyboard)
|
| |
 | | Rules for next years firefighting contest
|
|
Has anyone heard when next years rules will be out for the Trinity firefighting contest? Are there going to be any major changes or are they going to stay about the same? Thanks. Keith Keith Soldavin kas219@email.psu.edu (URL) (29 years ago, 5-Jul-97, to lugnet.robotics.handyboard)
|