To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *22464 (-20)
  Re: rotation sensor problem, again...
 
I had the same problem and I solved it with a msleep(50). msleep(10) is not enough. (...) (26 years ago, 3-Jul-00, to lugnet.robotics.rcx.legos)
 
  Re: battery life indicator
 
if((BATTERY/0x0016)<700) dlcd_show(LCD_BATTERY_X); I always put this line on my programs. BATTERY/0x0016 gives the value in V*100 of all batteries open circuit voltage. <700 is the limit for rotation sensors to work (all the other sensors have (...) (26 years ago, 3-Jul-00, to lugnet.robotics.rcx.legos)
 
  6.8nF Capacitor
 
I have got all the parts for building my HB except for a 6.8 nF 2% capacitor (component C6). Maplin Electronics have stop doing it and I am not sure where to try next. I am in the UK, does any body know if I can change the resistors in the infrared (...) (26 years ago, 3-Jul-00, to lugnet.robotics.handyboard)
 
  Re: running motors underwater
 
Cool Idea, but take it to it's logical extension ... Use the technic pnuematic elements to maintain positive air pressure in the motor housing. If you pump air into the tubes that you mentioned at a pressure higher than the water pressure, it will (...) (26 years ago, 3-Jul-00, to lugnet.robotics)
 
  Re: running motors underwater
 
(...) It depends alot on what kind of water it's in. Pure distilled water doesn't conduct very well. Water with any kind of ions (salt chlorine, flourine etc) will conduct much better and cause more heating. In addition, the electrolisis that occurs (...) (26 years ago, 3-Jul-00, to lugnet.robotics)
 
  Re: running motors underwater
 
(...) This sounds like a great application for temp sensors. :) I don't know if this has been brought up on this site before (it probabably has), but it might work pretty well to place a temp sensor directly against a motor's case, to measure the (...) (26 years ago, 3-Jul-00, to lugnet.robotics)
 
  running motors underwater
 
I haven't tried this myself, but I was just thinking that there could be many reasons why the motor heats up after running underwater. But first, do we know for sure that they are heating up more than they normally would? It would be interesting to (...) (26 years ago, 2-Jul-00, to lugnet.robotics)
 
  Re: interrupts for buttons
 
Sorry about the long delay, I've been away. Demo.c is inaccessable because it was written for 0.1.7 and I've not yet had the time to update it. Unfortunately, this is going to be a semi-major task and so will probably be one of the last things to (...) (26 years ago, 2-Jul-00, to lugnet.robotics.rcx.legos)
 
  Re: running the motors underwater
 
Are your tank filled with salt water? What is the electro-conductivity of your water? By the way, sinking a motor under water will damage lubricant inside the motor. I suggest you to pack the whole mechanic into a metal case, and seal the metal case (...) (26 years ago, 2-Jul-00, to lugnet.robotics)
 
  RE: running the motors underwater
 
I have run the Lego motors for long enough that they have gotten warm. This tells me that the holes you want to plug up would be needed as air vents. Not as much for circulation, but to let the air in the motor escape when it heats up and becomes (...) (26 years ago, 2-Jul-00, to lugnet.robotics)
 
  XCam2 remote aka Firecracker FREE with shipping
 
For all you Xcam2 owners (or who are planning on getting one), X10 is giving away their remote setup for free... (URL) (26 years ago, 1-Jul-00, to lugnet.robotics)
 
  Re: Sharp GP2D12-Sensor under sunlight?
 
I have three GP2D12s running on a Handyboard and they seem to run quite well in sunlight. In overcast or indirect light (shade) their performance seems identical to indoor light. In bright sunlight there seems to be a possible shortening of the (...) (26 years ago, 1-Jul-00, to lugnet.robotics.handyboard)
 
  Re: Call for Mac programmers
 
(...) I've posted the source code for MacNQC (sorry it took so long): (URL) there are any serious takers for continuing MacNQC development, please let me know. About the only thing I'd be concerned about is that the project should stay MPL'ed. Dave (...) (26 years ago, 1-Jul-00, to lugnet.robotics.rcx.nqc)  
 
  Sharp GP2D12-Sensor under sunlight?
 
Hi, I am working on a robot with the HandyBoard. I am thinking about using the Sharp GP2D12-Sensor because the other IR reflective sensors I use won't work under sunlight. I read the spec. sheet of GP2D02 and GP2D05, both of them mention that they (...) (26 years ago, 1-Jul-00, to lugnet.robotics.handyboard)
 
  Re: Scout Programming
 
I''ll need your help Dean . Can you send me the NQC code you used it for the scout ? Jeronimo Avelar (...) mounted (...) variations. (...) there (...) (26 years ago, 30-Jun-00, to lugnet.robotics.scout)
 
  RE: Motors spinning at startup
 
I also tried all sorts of capacitors, etc. in an attempt at solving this problem. While the capacitors helped to minimize the length of time before the motors calmed down, there was always a short period of motor craziness that never went away. I (...) (26 years ago, 30-Jun-00, to lugnet.robotics.handyboard)
 
  Re: Motors spinning at startup
 
I have been having the same motors spinning on powerup "problem" with my Handyboard. I tried various capacitor combinations on my modified servo motors to no effect. Fred M. finally provided the answer: (...) In short, there is nothing wrong with (...) (26 years ago, 30-Jun-00, to lugnet.robotics.handyboard)
 
  Re: sonar and overflow
 
Hi I think that the longest distance your able to measure is about 2.7m. The counter is 16 bit long and has no sign. But the integer is has a sign, so you can only use 15 bits, which is 32768. The counter increases each 0.5ns (pink book). Sound (...) (26 years ago, 30-Jun-00, to lugnet.robotics.handyboard)
 
  sonar and overflow
 
Greetings all, Has anyone managed to work out some code which checks the overflow bit for the counter used in the polaroid sonar code? At the moment mine distance readings seem to be maxing out around 1.5m or so, and I'm not sure if it's the timer (...) (26 years ago, 30-Jun-00, to lugnet.robotics.handyboard)
 
  Re: running the motors underwater
 
(...) The main problem is that the motor isn't water prof. It's rusting inside and or the grease is breaking down. The motor will heat up while in use. This would cause a sealed motor to push the air past the rotating axle. Ok, now when the motor (...) (26 years ago, 29-Jun-00, to lugnet.robotics.rcx)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR