 | | RE: New pbForth GUI
|
|
(...) Great! Maybe I can get another convert over to the dark side... The script uploads should work well too. And definitely try the SAVE-SYSTEM download. You need to load bigsys.srec firmware. Just type SAVE-SYSTEM after you've added whatever (...) (27 years ago, 17-May-00, to lugnet.robotics.rcx.pbforth)
|
| |
 | | RF vs IR link
|
|
Just a naive question: How much difficult would be to use the RF Cybermaster link with the RCX? (27 years ago, 17-May-00, to lugnet.robotics.rcx)
|
| |
 | | Re: lnp communication question
|
|
Remember the medium... cheap IR basically stinks for transmission. You get transients from the lights in your room, the outdoors, yadda, yadda. Luis (wishing for RF like the Europeans get ;) (...) ---...--- "Going to California with an aching in my (...) (27 years ago, 17-May-00, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: New pbForth GUI
|
|
(...) Just to confirm that, I successfully installed the GUI in my NT system (NT4.0 Build 1381, SP 5) following Jeff's procedure. It works great, no need of the giveio driver, no problems with the COM port though not having the Admin rights. Thanks (...) (27 years ago, 17-May-00, to lugnet.robotics.rcx.pbforth)
|
| |
 | | RE: how to drive extra steppers with handyboard
|
|
i ended up using two SSC II's to control the twelve servos on my robot because most of the time the servos connected to the XB would not work. the SSC II servos worked almost all the time. (URL) think this is the web address and the SSC II's connect (...) (27 years ago, 17-May-00, to lugnet.robotics.handyboard)
|
| |
 | | RE: New pbForth GUI
|
|
Jeff wrote... (...) Thanks Jeff, I was worried it might be taken the wrong way after I posted it... (...) I've snipped the rest of the description, but the result is that it works without the giveio driver, if I understand correctly. This is VERY (...) (27 years ago, 17-May-00, to lugnet.robotics.rcx.pbforth)
|
| |
 | | RE: how to drive extra steppers with handyboard
|
|
Try Scott Edwards SCC II Servo controller. (...) This message is for the named person's use only. It may contain confidential, proprietary or legally privileged information. No confidentiality or privilege is waived or lost by any mistransmission. (...) (27 years ago, 17-May-00, to lugnet.robotics.handyboard)
|
| |
 | | Expansion board cannot handle more than 2 servos
|
|
Hello, Reading the discussion on servos recently, I thought I'd share this info with you. I have advised a few student group projects involving servos and the XB and came to the conclusion that the XB cannot handle more than two or so servos. The (...) (27 years ago, 17-May-00, to lugnet.robotics.handyboard)
|
| |
 | | Re: Scout, Microscout & IR Remote
|
|
Dennis Williamson <dennis.NO@SPAM.netstrata.com> wrote (...) You're right. Sorry, my fault. There had been so much talking about this feature between the end of 1999 and the beginning of 2000 that I thought Eric's page included this info too, and (...) (27 years ago, 17-May-00, to lugnet.robotics)
|
| |
 | | RE: how many servos on handyboard?
|
|
Remeber also that you have to cut the motor power trace and use an external 5V source for the motors in this case. The HB itself will output 9.6 V from the motor ports. (...) This message is for the named person's use only. It may contain (...) (27 years ago, 17-May-00, to lugnet.robotics.handyboard)
|
| |
 | | Re: lnp communication question
|
|
(...) This suprises me. I have never heard of such high packet losses. How does dll do this? With some kind of ack and retry mechanism? dll seems reliable. Of course dll is going in the other direction. (27 years ago, 17-May-00, to lugnet.robotics.rcx.legos)
|
| |
 | | RE: New pbForth GUI
|
|
Ok, Ok, I'm an idiot....this is such a polite group that no one ever says RTFM ;>) Well, you did Ralph, but very, very nicely.... This GUI works great in NT (NT4.0 SP3), with very little work (once you start to think). Download and unzip TclTk ( I (...) (27 years ago, 17-May-00, to lugnet.robotics.rcx.pbforth)
|
| |
 | | how to drive extra steppers with handyboard
|
|
I'd like to build a six legged robot. that would need at least 12 servos. Is there a way to control 12 servos or more with the standard handyboard? someone said it's all in the code (using digital outputs) does that mean I could write the code to do (...) (27 years ago, 17-May-00, to lugnet.robotics.handyboard)
|
| |
 | | Re: Scout, Microscout & IR Remote
|
|
I didn't find any reference to the Microscout on his site. Dennis (...) Bad News: The next millenium starts on a Monday. Good News: You get the day off. (remove .NO and SPAM. to reply) (27 years ago, 17-May-00, to lugnet.robotics)
|
| |
 | | Re: how many servos on handyboard?
|
|
(...) Hi If you use the expansion board, you will loose analog input 0 und 1. These two inputs are multiplexed on the exp board, so you get some more analog ports. -Martin (27 years ago, 17-May-00, to lugnet.robotics.handyboard)
|
| |
 | | Re: Scout, Microscout & IR Remote
|
|
(...) light (...) light (...) be (...) Sure it works :-) Probably the first post that mention this feature is by Eric Brok in Nov 1999: (URL) Eric's great site you will find many details about Scout to Microscout interfacing, as well as Scout to (...) (27 years ago, 17-May-00, to lugnet.robotics)
|
| |
 | | Re: lnp communication question
|
|
You just pass an array and give the length, to send it. In theory you can send packets with a size up to 255 bytes (look in this group, the info is in here somewhere), but sending 1 byte has a packet loss of aprox. 1% and 4 bytes aprox. 10%, over (...) (27 years ago, 17-May-00, to lugnet.robotics.rcx.legos)
|
| |
 | | Re: Scout, Microscout & IR Remote
|
|
That is _very_ cool! I just tried it out and it works! THANKS! Dennis (...) -- Dennis Williamson - Certified Y2K Complacent Bad News: The next millenium starts on a Monday. Good News: You get the day off. (remove .NO and SPAM. to reply) (27 years ago, 17-May-00, to lugnet.robotics)
|
| |
 | | Re: how many servos on handyboard?
|
|
The base Handy Board is designed to control 4 DC motors. The DC motor output ports CAN be used to control 4 (four) stepper motors. Remember that a stepper motor needs a square wave pulse continually sent to the motor for operation, and the mark / (...) (27 years ago, 17-May-00, to lugnet.robotics.handyboard)
|
| |
 | | Re: how many servos on handyboard?
|
|
(...) The deal is this: Servos are different from plain old DC motors. They have gearing and position control circuitry built in. There are four DC motor ports on the basic HB, but no ready-made servo ports. The dual servo routine described on the (...) (27 years ago, 17-May-00, to lugnet.robotics.handyboard)
|