To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *2166 (-10)
  Re: your mail
 
(...) Get your soldering iron, some solder labeled electronics use, some old circuit board, and solder away. Or, you could take an old computer board and desolder some components from it, and re-solder them in. Just get in there and do it. You know (...) (30 years ago, 19-May-97, to lugnet.robotics.handyboard)
 
  Re: Vector 2x compass
 
A mistake has been found on the V2X schematic, the M/S pin on the compass needs to be grounded. I don't know what it is, everytime I publish something, I make a mistake. (30 years ago, 19-May-97, to lugnet.robotics.handyboard)
 
  Strange HB problems
 
Over the past two days I have had two problems with my HB that I can't explain. Maybe you you can help. 1. I wrote a simple program to test out my motors that consists of the motor, sleep, and beep commands. Once in a while I get an error back while (...) (30 years ago, 19-May-97, to lugnet.robotics.handyboard)
 
  (no subject)
 
Another note on soldering.. Heat control is VERY important.. Not so much being able to adjust the heat, as having a temperature-controlled iron. The "cheaper" irons get hotter or colder with the load (speed of soldering) as well as the room (...) (30 years ago, 19-May-97, to lugnet.robotics.handyboard)
 
  Re: Soldering (fwd)
 
Often novices miss the single most fundamental point about soldering: you don't use the iron to melt the solder (99% of the time) -- you heat the component leads and let them melt the solder. To initially transfer heat effectively to the leads, a (...) (30 years ago, 18-May-97, to lugnet.robotics.handyboard)
 
  Re: Soldering
 
(...) experience >at all with soldering. (...) become more >adept at this sort of stuff. And what type of solder should I use? Shane is right, you'll find using very thin solder works much better. Along with a fine tip, you'll want to use a low (...) (30 years ago, 18-May-97, to lugnet.robotics.handyboard)
 
  Soldering/ Second processor
 
->Hi, I'm planning to purchase the handyboard as a kit from Digital Mirco System, since I'm a bit tight with money. However, I'm a bit hesitant (...) soldering. The trick is to use THIN 60/40 solder with flux core. Around 0.71 mm thickness is good. (...) (30 years ago, 17-May-97, to lugnet.robotics.handyboard)
 
  Re: Vector 2x giving me lots of trouble...
 
Well, I seemed to have narrowed down the problem I was having with the Vector2x compass. It was functioning fine... All I had to do was write clean code that called comp_disable(1) at the end. When my code wasn't doing that, the compass IRQ routines (...) (30 years ago, 17-May-97, to lugnet.robotics.handyboard)
 
  '97 Intel ISEF
 
This last week was the 1997 Intel International Science and Engineering Fair (ISEF), held in Louisville, Kentucky. While I don't have a list of winners/losers, I do have some things to say about it. There were five robots in the engineering (...) (30 years ago, 17-May-97, to lugnet.robotics.handyboard)
 
  (no subject)
 
Hi, I'm planning to purchase the handyboard as a kit from Digital Mirco System, since I'm a bit tight with money. However, I'm a bit hesitant about assembling the kit because I have no experience at all with soldering. Can anyone recommend something (...) (30 years ago, 17-May-97, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR