To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.roboticsOpen lugnet.robotics in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Robotics / *1181 (+10)
  Re: Using RC cars for robot
 
(...) We have successfully integrated a Traxxas RC car with the Handy Board. The vehicle uses a standard servo for steering and an electronic speed control (same behavior as a servo.) Since the HB can control 2 servos this works well. In this case (...) (30 years ago, 2-Jan-97, to lugnet.robotics.handyboard)
 
  pcode downloading
 
Happy New Year! I'm putting together a HandyBoard and am stuck at the point where pcode_hd.s19 is downloaded. Some details: Have a chip labled SIPEX SP232ACP as a substitute(?) for MAX232. During downloading using DLM the board syncs OK but (...) (30 years ago, 2-Jan-97, to lugnet.robotics.handyboard)
 
  Problem Downloading Pcode!!!!
 
Hi, I'm really stuck. I got a facory fresh HB, instead of a Motorola it had a Toshiba C11W chip. When dowloading pcode_hb.s19 IC Win 95 says "CONFIG register required resetting. Please place in download mode again." Help, my scince project is due in (...) (30 years ago, 2-Jan-97, to lugnet.robotics.handyboard)
 
  Coparison of Sensors
 
Hi, I know this is probably a stupid question to you, but I wrote a program to compare sensors. But it doesn't seem to work. Can anyone help?? Here it is (30 years ago, 2-Jan-97, to lugnet.robotics.handyboard)
 
  Re: pcode downloading
 
Here is the relevant part of the test instructions: Finally, the MAX232's ability to transmit data to the host computer is tested. Again using pin 7 of J9 as a ground reference, measure the voltage at pin 3 of J9. This is the MAX232's serial output. (...) (30 years ago, 3-Jan-97, to lugnet.robotics.handyboard)
 
  Re: pcode downloading
 
(...) : (...) I get -8.9v when its not jumped. When jumped I get some floating values in the mV range. I checked all of the solder joints. Changed power supplies. Removed and reseated the chip. Checked power and continuity at various points around (...) (30 years ago, 3-Jan-97, to lugnet.robotics.handyboard)
 
  Re: pcode downloading
 
(...) OK, well I think it is isolated at the pseudo-MAX232 chip. Did you get the +10 v power supply pin on the p-MAX ok? It's at pin 2. Measure it w/r/t ground and you should get +10v. Before you order a real Maxim, check the polarity of your (...) (30 years ago, 3-Jan-97, to lugnet.robotics.handyboard)
 
  Config 0C / 0D
 
Hi, I know this is an old chestnut but believe me I have searched the mail archive and nothing quite matches what I'm seeing. I have a handyboard which I made and which seems to work perfectly. However, I have to download (using hbdl) with the (...) (30 years ago, 3-Jan-97, to lugnet.robotics.handyboard)
 
  Re: Coparison of Sensors
 
(...) Looks like you got too many semi-colons. Take out the semi-colons on all the while lines where you want the while to do the following thing. The process is getting to the "while(!start_button());" line and staying there. Also you have too many (...) (30 years ago, 3-Jan-97, to lugnet.robotics.handyboard)
 
  Re: Coparison of Sensors
 
(...) I agree. You should only have a semi-colon after a while if you dont want that while to loop through any instructions. A semi-colon after a while tells the compiler that all you want to do is continuously test the while condition until it (...) (30 years ago, 3-Jan-97, to lugnet.robotics.handyboard)

Next Page:  5 more | 10 more | 20 more
Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR