 | | Re: Why do it? Was: multi-device output controller
|
|
My original message described the controller with two inputs, one for device selection and one for device power. This could easily be connected to whatever power source the user desires. (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | RE: Muscle wire and alternatives
|
|
I have connected nitinol to Lego and it can melt the ABS plastic...be careful. Rich (URL) Message----- From: Jim Choate [mailto:ravage@EINST...N.ssz.com] Sent: Friday, March 26, 1999 11:36 AM To: lego-robotics@crynwr.com Subject: Muscle wire and (...) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | RE: Why do it? Was: multi-device output controller
|
|
(...) Measuring PWM is not difficult, but it would involve a micro (PIC12C508 anyone?) dedicated to the task and then you would have to get it to drive the RCX, which means motor drivers, etc. If you are willing to spend $50 and LOTS of time, then (...) (28 years ago, 27-Mar-99, to lugnet.robotics, lugnet.robotics.rcx.pbforth)
|
| |
 | | Why do it? Was: multi-device output controller (fwd)
|
|
----- Forwarded message from Ralph Hempel ----- From: "Ralph Hempel" <rhempel@bmts.com> Subject: Why do it? Was: multi-device output controller Date: Fri, 26 Mar 1999 22:17:57 GMT With all of the talk about RS232 converters, and PWM decoders, why (...) (28 years ago, 27-Mar-99, to lugnet.robotics)
|
| |
 | | Re: LEGO 9V battery box as project container
|
|
(...) Can anyone guess how long a 9 volt battery power supply like this will last compared to 6 AA batteries? This does seem like a good small power solution and project box. <ICS> -- Did you check the web site first?: (URL) (28 years ago, 26-Mar-99, to lugnet.robotics)
|
| |
 | | RE: Why do it? Was: multi-device output controller (fwd)
|
|
(...) Hmmm, the RCX tower is a pretty effective RS232 converter...and you will still need to write special software for the RS232 convertor's interface to the PC. Like I said, its cheaper and quicker to buy a second RCX from Pitsco... Cheers, Ralph (...) (28 years ago, 27-Mar-99, to lugnet.robotics)
|
| |
 | | RE: Why do it? Was: multi-device output controller (fwd)
|
|
----- Forwarded message from Ralph Hempel ----- Subject: RE: Why do it? Was: multi-device output controller (fwd) Date: Sat, 27 Mar 1999 02:17:09 GMT (...) Hmmm, the RCX tower is a pretty effective RS232 converter...and you will still need to write (...) (28 years ago, 27-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Polarity Switch = Pressure Switch
|
|
(...) Good job, Ralph! The most compact solution seen up to now for a pneumatic switch. Mario (28 years ago, 27-Mar-99, to lugnet.build, lugnet.robotics)
|
| |
 | | analog inputs on expansion board
|
|
Hi, Two questions: 1) When I plug a Lego reflectance sensor into the expansion board it seems to work fine. When I use the angle sensor it seems to work fine. When I plug them in at the same time the angle sensor stops working. No change to the (...) (28 years ago, 27-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Handy Board inputs
|
|
Hi, my name is Becky Browning. I am currently working on building a robot using the Handy Board. I am having considerable troubles though getting either the digital or analog inputs to work. Right now I have analogs ports 0 and 1 working with (...) (28 years ago, 27-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Angle Sensor
|
|
Hi, Can someone tell me how the angle sensor works? Is it giving a RAW value back, or maybe even a real angle (between 0 and xxx, with step 1)? Where can I get the angle sensor in Europe (The Netherlands)? Thanks in advance... Michel -- Did you (...) (28 years ago, 27-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Handy Board inputs
|
|
Hi Becky, If you are using the HB with the expansion board, you *do* need new library files loaded. Check the web site at: (URL) easiest way to run new library files is to edit lib_hb.lis to include them. To test the HB inputs w/o the expansion (...) (28 years ago, 27-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | Re: Angle Sensor
|
|
(...) The Lego rotation sensor counts each rotation in 16 steps starting from 1 (no. # 2 to 17 for the first full rotation). If the rotation goes backwards the count is negative (no. # 0 to -15 for the first full backward rotation). The count is (...) (28 years ago, 27-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Angle Sensor
|
|
One of the best suggestions (maybe from Ralph Hempel??) that I have seen for this sensor is to gear it up (down?) to get the desired rotational resolution. -Rob Doucette. Franz-Michael S. Mellbin wrote in message ... (...) (no. (...) 1 + (...) that (...) (28 years ago, 27-Mar-99, to lugnet.robotics)
|
| |
 | | RE: Angle Sensor
|
|
(...) Nope, wasn't me...I'll bet the fancy LEGO milling machine does something like it though... Maybe I should buy a rotation sennsor first :-) Cheers, Ralph Hempel - P.Eng ---...--- Check out pbFORTH for LEGO Mindstorms at: (URL) ---...--- Reply (...) (28 years ago, 27-Mar-99, to lugnet.robotics)
|
| |
 | | Re: Angle Sensor
|
|
Well, then I guess I need to build my own rotation sensor using a "Potmeter" (variable resistor) because I need a real angle, actually I need an angle per time value. Is this is possible? I saw something about this on a website in the mindstorms (...) (28 years ago, 27-Mar-99, to lugnet.robotics)
|
| |
 | | Help needed!
|
|
Hi, I have assembled my recently bought Handy Board kit and have run into major problems: In paragraph 6.0.5 of the assembly manual, the Handy Board is tested for the microprocessor and memory circuits. After powering up the board and running IC (...) (28 years ago, 28-Mar-99, to lugnet.robotics.handyboard)
|
| |
 | | King of the hill
|
|
Howdy, I'm looking for fellow Mindstormers in the Houston, Texas area for sparing. Basicaly, I want to try a "king of the hill" type of competition. White circular field, black border (say black electrical tape), last robot inside the field wins. (...) (28 years ago, 28-Mar-99, to lugnet.robotics.events)
|
| |
 | | Light Sensor Non Destructive Mods
|
|
Hi All, I've just added a new page to my website that describes a non-destructive mod to the light sensor that actually allows it to read ambient light! (URL) The range is <10 for a dark box and >90 for a halogen lamp about 6 feet away. It's really (...) (28 years ago, 28-Mar-99, to lugnet.robotics, lugnet.robotics.rcx.pbforth)
|
| |
 | | Java class libraries for HandyBoard
|
|
Users interested in running Java on HandyBoard can now download demonstration application and a set of library class files at (URL) Gasparik (28 years ago, 28-Mar-99, to lugnet.robotics.handyboard)
|