 | | Re: NMRA2003 Friday install
|
|
(...) (URL) I have 4 modules (the wooden things) and 4 legs.... should I bring these??? Jeff VW (21 years ago, 14-Jul-03, to lugnet.org.ca.rtltoronto)
|
| |
| | Re: NMRA2003 Friday install
|
|
(...) sounds good (...) Had? Have! I could open a Commodore museum--Pet (4032x2, 8032-just the motherboard) Vic, 64, 128, SX64 and many many peripherals--4040, 8250 dd for the Pets, 1541x4, 1571x2, 1581x1 drives for the 64, et al, modems, joysticks, (...) (21 years ago, 14-Jul-03, to lugnet.org.ca.rtltoronto)
|
| |
| | Re: NMRA2003 Friday install
|
|
(...) I filled the module north of me, is that the same module? (URL) (...) THink we got htat covered--the RCX power may be a different issue--the wall warts have to make it to the outlets from wherever the RCX;s are in the layout. I'll have my (...) (21 years ago, 14-Jul-03, to lugnet.org.ca.rtltoronto)
|
| |
| | Re: DCC party
|
|
(...) makes (...) properly. Which color wires did you end up soldering to the headlight connector? Also, IIRC the default CV values for the headlight don't work very well. Here's some settings I used to setup the decoder for controlling the (...) (21 years ago, 14-Jul-03, to lugnet.org.ca.rtltoronto)
|
| |
| | Re: NMRA2003 Friday install
|
|
(...) You can park the car at our house no problem. I unfortunately cannot offer you a place to stay, but the truck is not an issue, you can leave it here. Calum (21 years ago, 14-Jul-03, to lugnet.org.ca.rtltoronto)
|
| |
| | Re: NMRA2003 Friday install
|
|
(...) I can bring my PalmVx which functions as a remote if needed. (...) I can bring them back as well, no problem. What I'll do is this. We'll set up on Friday, and I'll bring out my major conponents (red station, yellow freight station) then (...) (21 years ago, 14-Jul-03, to lugnet.org.ca.rtltoronto)
|
| |
| | Re: NMRA2003 Friday install
|
|
(...) Here's what I can offer. Since Altenburg will be at the train show, there will be just enough space to fold out my couch. So you are welcome to stay with me, however I don't have extra parking, so the truck would have to stay either at the (...) (21 years ago, 14-Jul-03, to lugnet.org.ca.rtltoronto)
|
| |
| | Re: NMRA2003 Friday install
|
|
(...) <snip> (...) I have an extra base plate Dave... (...) I have some extra straights, I bring what I have... (...) Were you refering to me when you said Jeff? I can rebuild the round (8 sided) building, and I can bring the Battery pack towers (I (...) (21 years ago, 14-Jul-03, to lugnet.org.ca.rtltoronto)
|
| |
| | Re: NMRA2003 Friday install
|
|
(...) Hey Dave, I have four legs and 1 module that go beside(south of) the Dam. I also found 3 extra modules as well, should I bring these? (...) I can bring one (maybe two) (...) I will have 2 1.0's there, one may be used in the crane :) (...) I'll (...) (21 years ago, 14-Jul-03, to lugnet.org.ca.rtltoronto)
|
| |
| | Re: 45 Degree Crossing Ready
|
|
(...) Very nice Derek, I go as far as cutting baseplates, track is a completly different issue.... (21 years ago, 14-Jul-03, to lugnet.org.ca.rtltoronto)
|
| |
| | Re: NMRA2003 Friday install
|
|
(...) I can do that. Wasn't sure what needed to be done, was going to ask later. Just figured that was a convenient place to put one. (...) Ok, lets just say the outside loop is the master control loop and all other RCXs will key off this loop. (...) (21 years ago, 14-Jul-03, to lugnet.org.ca.rtltoronto)
|
| |
| | Re: 45 Degree Crossing Ready
|
|
(...) It wasn't sarcastic. I really like it. It's better than what I could do. Dave K (21 years ago, 14-Jul-03, to lugnet.org.ca.rtltoronto)
|
| |
| | Re: NMRA2003 Friday install
|
|
(...) <snip> . (...) <snip> (...) Is your RCX picking up the signal from 'the main loop'? I guess the 'main loop' is going to be the outside loop--the RCX connected to that loop needs to be visible for the remote to work. All other 'slave' RCX's can (...) (21 years ago, 14-Jul-03, to lugnet.org.ca.rtltoronto)
|
| |
| | Re: 45 Degree Crossing Ready
|
|
(...) I'll take that sarcastically. :-) Reserve comment until you've seen it in person. Derek (21 years ago, 14-Jul-03, to lugnet.org.ca.rtltoronto)
|
| |
| | Re: NMRA2003 Friday install
|
|
(...) I'm taking Friday off, so I can do my best to be there at 5pm as well. Downtown to Airport at that time is not pretty. :-) (...) You sound like a good candidate to drive in. I've got a trolley, assuming I can fit it in my car with the rest of (...) (21 years ago, 14-Jul-03, to lugnet.org.ca.rtltoronto)
|
| |
| | Re: NMRA2003 Friday install
|
|
In lugnet.org.ca.rtltoronto, Calum Tsang wrote: <snip> (...) <snip> (...) I'll have my cell as well, I'll e-mail it to y'all. If anyone has a couch available friday and sat. night, it would be appreciated. I'll pack my sleeping bag as well. Dave K (21 years ago, 14-Jul-03, to lugnet.org.ca.rtltoronto)
|
| |
| | Re: NMRA2003 Friday install
|
|
(...) Whats our sequence to setup the layout? I think it's JeffE/Derek first, right? I'll try to be there at 6PM, as I'm not sure if I can leave early from work. (...) I should be there both Sat and Sun. (...) Probably. If anyone from the rest of (...) (21 years ago, 14-Jul-03, to lugnet.org.ca.rtltoronto)
|
| |
| | Re: NMRA2003 Friday install
|
|
(...) THis is the e-mail I got-- " CONFIRMATION Thanks for your application for the our upcoming exciting train show on July 19,20 at the International Centre. We have had an excellent response from the dealers and exhibitors which will result in (...) (21 years ago, 14-Jul-03, to lugnet.org.ca.rtltoronto)
|
| |
| | Re: 45 Degree Crossing Ready
|
|
In lugnet.org.ca.rtltoronto, Derek Raycraft wrote: <snip> (...) *snif!* It's so... Beautiful! Wonderfully done! Dave K (21 years ago, 14-Jul-03, to lugnet.org.ca.rtltoronto)
|
| |
| | NMRA2003 Friday install
|
|
So, when exactly are we meeting for Friday's setup? Trying to decide between one module in the Accord or two in the Chick Magnet. Calum (21 years ago, 14-Jul-03, to lugnet.org.ca.rtltoronto)
|
