|
|
 | | Re: Voting page for 9906
|
| John VanZwieten <john_vanzwieten@email.msn.com> wrote in message news:FFwpGz.86r@lugnet.com... (...) they meet the flat part of the door. I'm confused... Isn't this drawn when the stud2 primitive is called? Adam (25 years ago, 4-Aug-99, to lugnet.cad.dev.org.ldraw, lugnet.cad.dev)
| | | | | Re: Voting page for 9906
|
| (...) things i know about: what exactly is missing fron the box and switch??? i cant see any details on the part that can be seen from the outside that are missing except the clip. i will add the rectangular face part of the clip to the lid part if (...) (25 years ago, 3-Aug-99, to lugnet.cad.dev.org.ldraw, lugnet.cad.dev)
| | | | | Re: Voting page for 9906
|
| (...) Okay, I checked my canopies, and here is what I found: 2 are as John is describing. Very little fading from Dark to light gray, no gray line on the inside, etc. These correspond to my Y-wing sets. 6 are as I'm describing. Fade from dark to (...) (25 years ago, 3-Aug-99, to lugnet.cad.dev.org.ldraw, lugnet.cad.dev)
| | | | | Re: Voting page for 9906
|
| Voting part comments: 2400, 6105: The 1/2 cylinder studs on the doors need 4-4edge.dat's where they meet the flat part of the door. 2500c01: I don't think the lights are done quite right here. There's a reference to a 4-4cone1.dat, but I don't have (...) (25 years ago, 3-Aug-99, to lugnet.cad.dev.org.ldraw, lugnet.cad.dev)
| | | | | Re: Voting page for 9906
|
| (...) news:FFuFFw.Cr0@lugnet.com... (...) Ah. I didn't realize that. No problem then. (...) Really? I'll have to compare all of mine when I get home (I have 8). Don't forget to dither(?) the dark gray to light gray, please! :) I could deal with a (...) (25 years ago, 3-Aug-99, to lugnet.cad.dev.org.ldraw, lugnet.cad.dev)
| | | | | Re: Voting page for 9906
|
| Jeff Stembel <Dragonelf1@aol.com> wrote in message news:FFuFFw.Cr0@lugnet.com... (...) The insertion point is the center of the cylinders. This makes it much easier to rotate on the z axis, and to rotate on the x axis then place in its vertical (...) (25 years ago, 3-Aug-99, to lugnet.cad.dev.org.ldraw, lugnet.cad.dev)
| | | | | Re: Voting page for 9906
|
| (...) Well, in LDLite, it looks like there is a faded crosswalk when shading is turned on. It looks really bad, IMO. (...) Oops, my bad. Yes, I meant 609p01. Thanks for changing the color. Now it'll match the current road plates. Talkin' 'bout the (...) (25 years ago, 3-Aug-99, to lugnet.cad.dev.org.ldraw, lugnet.cad.dev)
| | | | | Spline-generator
|
| Hi, After experimenting a bit with the current tools for creating flexible parts I had a lot of problems to place and orientate the hoses using Bezier-curves. I've looked around a bit and found some examples using multi-point splines. Main different (...) (25 years ago, 3-Aug-99, to lugnet.cad.dev.org.ldraw)
| | | | | Re: Voting page for 9906
|
| (...) i would just like to say that i am prepared to admit that the roadplate parts probobly were not redy for voting on but on the 32 x 32 raised with ramp the mistakes on the corners and also the line in the pit were all honest mistakes. (25 years ago, 3-Aug-99, to lugnet.cad.dev.org.ldraw, lugnet.cad.dev)
| | | | | Re: Voting page for 9906
|
| (...) i promise to fix the pit extra line asap.also about the corners... i can fix those as well. thanks for pointing out the mistake. (...) my mistake. i thought i could make this by changing the color of the grey bits on the dashed roadplate to (...) (25 years ago, 3-Aug-99, to lugnet.cad.dev.org.ldraw, lugnet.cad.dev)
|
|
