 | | Re: OMR Submission and Storage
|
|
Tim Courtney <tim@zacktron.com> wrote in message news:4.2.0.58.199907...omm.com... (...) You can--using LDAO's editor. But you still would have to go through and figure out all the pivot points, where the hinge piece should be compared to where it (...) (25 years ago, 23-Jul-99, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: OMR Submission and Storage
|
|
I believe IIRC stands for If I Remember Correctly. IIDRC :) please do correct me. Ryan ***...*** REPLY SEPARATOR ***...*** (...) was pretty much (...) then... (...) have the same (...) quality models. (...) some point... (...) (25 years ago, 23-Jul-99, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: OMR Submission and Storage
|
|
(...) Hehe :) (...) I didn't catch that thread... (...) Good, my memory isn't failing in old age ;) (...) *nark* *nark* *nark* :) -Tim <>< (URL) timcourtne ICQ: 23951114 Get paid to surf the web! Visit: (URL) (25 years ago, 23-Jul-99, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: OMR Submission and Storage
|
|
(...) It would be easier if you could move a bunch of parts as a group all at once... 8< snip the light.dat trick explanation... Thanks... I get it now, I guess I'm not that serious an LDraw user :) -Tim <>< (URL) timcourtne ICQ: 23951114 Get paid (...) (25 years ago, 23-Jul-99, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: OMR Submission and Storage
|
|
(...) Ok... BTW, what does IIRC mean?? -Tim <>< (URL) timcourtne ICQ: 23951114 Get paid to surf the web! Visit: (URL) (25 years ago, 23-Jul-99, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: OMR Submission and Storage
|
|
Thanks Bram. I was thinking along that line, but forgot about light.dat That would work just fine. Ryan ***...*** REPLY SEPARATOR ***...*** (...) plate (...) means (...) 4275/4276, you (...) light.dat as a (...) couple (...) (25 years ago, 23-Jul-99, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: OMR Submission and Storage
|
|
(...) from (...) now. ;) I wouldn't expect a lazy person like you to go searching for a link :) I didn't know if you might happen to know what it was off the top of your head. I know that would be asking a lot :) (...) you??......Good (...) types (...) (25 years ago, 23-Jul-99, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: OMR Submission and Storage
|
|
Tim Courtney <tim@zacktron.com> wrote in message news:4.2.0.58.199907...omm.com... (...) No, that would take too much time to fix all the submodels. The center of a submodel is just the 0,0,0 point of the submodel file. Like Bram mentioned, putting (...) (25 years ago, 23-Jul-99, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: OMR Submission and Storage
|
|
(...) What is the point of doing a set in ldraw if it is not going to be submitted to the OMR? Since we have the models.sets, we don't need the OMR group. If I remember correctly, Todd originally made models.sets *for* the OMR (or at least that was (...) (25 years ago, 23-Jul-99, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: excuses website (formerly posted in a dat-group)
|
|
(...) Problem is may be is in your URL: (URL) you have backlash just before image filename it must be normal slash as follows (URL) well Gintaras (25 years ago, 23-Jul-99, to lugnet.cad.dev.org.ldraw)
|
