 | | Re: Part Numbering Crisis in LDraw
|
|
(...) LDAO could be set up to ignore any unique marker in the descriptive name. At this time, any user can do it themselves, by editing the ldraw.ini. The default settings ignore moved files, 'delete me' files, and light.dat. (...) I'm assuming (...) (26 years ago, 10-Mar-99, to lugnet.cad.dev)
|
| |
| | lightsaber
|
|
steve, can i have your lightsaber .dat files? (26 years ago, 10-Mar-99, to lugnet.cad.dev)
|
| |
| | Re: Part Numbering Crisis in LDraw
|
|
(...) Well then; Surprise! :-P The following 7xxxx numbers are embossed on elements: 70163 Metal Counter-Weight Wedge 70942 1x2 Tile, Top Center Ball: Chrome 70969 Mini-Figure Exhaust Pipe, Right: Chrome 70972 Mini-Figure Exhaust Pipe, Left: Chrome (...) (26 years ago, 10-Mar-99, to lugnet.cad.dev)
|
| |
| | Re: Part Numbering Crisis in LDraw
|
|
(...) You rang? :-P The pink raft (dinghy is too much typing :-) can be seen here: (URL) Now the canoe is a different matter....... Oh gawd. :-P When even *I* get the joke, it's old news Terry. -- joshua (26 years ago, 10-Mar-99, to lugnet.cad.dev)
|
| |
| | Re: Part Numbering Crisis in LDraw
|
|
Steve Bliss wrote in message <36e52d27.5283445@lu...et.com>... (...) Not that I think this should affect the outcome of this discussion or anything, but there is at least one part that has a 7xxxx number stamped on it. The gold insectoid eye (i.e. (...) (26 years ago, 10-Mar-99, to lugnet.cad.dev)
|
| |
| | Re: [Parts] Plate 1x1 Round with Towball
|
|
(...) Again, confusion (<g>): The question on the table is whether the BALL has a hole in it, NOT the stud... (All of mine have always had a hole through the stud). Of course, you did write "hole in the tow ball" earlier, so I'm presuming that this (...) (26 years ago, 10-Mar-99, to lugnet.cad.dev)
|
| |
| | Re: [Parts] Plate 1x1 Round with Towball
|
|
(...) No. I am very distinctly talking about the older item. I'm not sure what the new item you are talking about, but both of the elements that I described were in my collection years before Dk Grey became available, and both have a ball and a (...) (26 years ago, 10-Mar-99, to lugnet.cad.dev)
|
| |
| | Re: Technic Axles - go rounded?
|
|
(...) I've actually run into a problem once with the axle being too long. I was trying to model a craft that I built, and I ended up fudging the virtual model by pushing the axle into the motor, because otherwise it popped through the radar dish on (...) (26 years ago, 10-Mar-99, to lugnet.cad.dev)
|
| |
| | Re: [Parts] Plate 1x1 Round with Towball
|
|
(...) There's one hole through the stud and the base where it is placed. Leonardo (26 years ago, 10-Mar-99, to lugnet.cad.dev)
|
| |
| | Re: Part Numbering Crisis in LDraw
|
|
(...) True. As the best way to keep everyone at least somewhat happy. (...) I don't want to over-use 3-digit numbers. Only where necessary and unavoidable. For instance; The complete yellow dinghy does have the correct number. So we can make a (...) (26 years ago, 9-Mar-99, to lugnet.cad.dev)
|
