 | | Gears (Was: Voting Open...)
|
|
(...) I think I've done all except for the largest. (...) DSCTS gears? Are they the same as Classic European Pre-Technic gears? (URL) is there yet another kind? The euro gears are not at all compatible with Samsonite gears. Where can a picture of (...) (24 years ago, 23-Aug-00, to lugnet.cad.dev)
|
| |
| | Re: Voting Open for LCAD Parts Update 2000-02
|
|
In lugnet.cad.dev, Steve Bliss writes: [snip] (...) O.K. Ornamented it will be then. By the way, Steve, Did you already notice that I've started to send "suggested update revisions" to your adress "partsref@worldnet.att.net" ? (24 years ago, 22-Aug-00, to lugnet.cad.dev)
|
| |
| | Re: cannot connect to site / lack of support from MediaOne.net - DAY THREE (KMM78820C0KM) [lego]
|
|
I have no idea if this is of any help but, I also use mediaone for web access and I can go to www.ldraw.org fine... I have no idea about all the proxy stuff so I cant help you there. HTH (...) [4.24.144.73] (...) (24 years ago, 22-Aug-00, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: cannot connect to site / lack of support from MediaOne.net - DAY THREE (KMM78820C0KM) [lego]
|
|
(...) [snip] (...) Didn't someone suggest using an anonymous proxy that might be located a few hops closer to ldraw.org? There's a list of proxy sites here: (URL) don't work. The proxy at webcache worked for me. YMMV... Or you could sample the free (...) (24 years ago, 22-Aug-00, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: Voting Open for LCAD Parts Update 2000-02
|
|
(...) Right. As I understand, this brick appeared with several different colors of printing, but always on the same color brick. This approach (hard-coding the brick color, but allowing the pattern color to 'float') has been done in a few other (...) (24 years ago, 22-Aug-00, to lugnet.cad.dev)
|
| |
| | Stages, woo-hoo! (Was: The Artemis Project)
|
|
(...) The single greatest contribution (IMO) that the Artemis Project has to offer is the concept of Stages, its OO approach to model and submodel storage. Essentially, a model can be associated with a Stage or a set of attributes -- origin offset, (...) (24 years ago, 22-Aug-00, to lugnet.cad, lugnet.publish, lugnet.cad.dev)
|
| |
| | cannot connect to site / lack of support from MediaOne.net - DAY THREE (KMM78820C0KM) [lego]
|
|
This is the *third* day I have been trying to access "www.ldraw.org" without success. I have *yet* to receive a response from a human being at Media One. No phone calls, no email (other than the original email from some anonymous techie at Media One (...) (24 years ago, 22-Aug-00, to lugnet.cad.dev.org.ldraw)
|
| |
| | Re: Voting Open for LCAD Parts Update 2000-02
|
|
(...) This is by design then? (...) No preference here; I just think that (for consistency) the origin should be between two studs (if possible), and visible when the model is viewed from the front or back or the sides (if possible). This one is (...) (24 years ago, 22-Aug-00, to lugnet.cad.dev)
|
| |
| | Re: Voting Open for LCAD Parts Update 2000-02
|
|
(...) I considered posting the L3P -check output as a link on the voting page. (...) How about a parrot w/o decorative printing? ;) (...) It would be very nice if L3Lab had a menu command for L3P-check'ing the current file. A little dialog to set (...) (24 years ago, 22-Aug-00, to lugnet.cad.dev)
|
| |
| | Re: Voting Open for LCAD Parts Update 2000-02
|
|
(...) Note to everyone (repeating myself from just a few minutes ago): the one thing that practically *can't* be changed after a part is released is the orientation and positioning! So it may seem picayune to argue about these things, but it is very (...) (24 years ago, 22-Aug-00, to lugnet.cad.dev)
|
