Subject:
|
Re: Hose spreadsheet now available
|
Newsgroups:
|
lugnet.cad
|
Date:
|
Thu, 15 Apr 1999 14:28:55 GMT
|
Viewed:
|
2391 times
|
| |
|
|
I didn't get one. I'll try re-downloading to see if that works
Ryan
*********** REPLY SEPARATOR ***********
On 4/15/99, at 9:57 AM, John VanZwieten wrote:
> No, I mean the hsreadme.txt that was included in the zip file. I'd rather you
> try to make a hose based on those instructions so that I can see if
> more/different explaination is neccessary.
>
> -John Van
>
> SCOTT R DENNETT wrote in message <199904142255390990.0213434A@agate.net>...
> You mean in the spreadsheet itself? Yes but I still dont understand
> what the control points are. Are the endpoints going to be the first parts
> in the section of spherical parts, or is it going to be the more cylandrical
> parts. I'm sorry but I don't know what the part #'s are right now. I think I
> can
> figure out how to do the endpoints if I know which piece it is going to be,
> but
> it is the control points that I don't understand. Does that help?? Then how do
> I get it to change the coordinates down below?
> Ryan
>
> *********** REPLY SEPARATOR ***********
>
> On 4/14/99, at 9:31 PM, John VanZwieten wrote:
>
> > Did you read the readme file?
> >
> > In lugnet.cad, Ryan Dennett writes:
> > > Ok, I will need some help, because I've never used Excel the proper way :)
> > > I assume all I need to do is to enter in the x y z coordinates of the=
> > > endpoints
> > > and the control points, but what are these points? Then after I put them=
> > > in,
> > > what do I do?
> > > Thanks
> > > Ryan
> > >
> > > *********** REPLY SEPARATOR ***********
> > >
> > > On 4/14/99, at 3:35 PM, John VanZwieten wrote:
> > >
> > > > > Hey, I wasn't flaming you it's just that various people have asked
> > > > > about it and I never saw responses, so I just figured..
> > > > > I meant no offense.
> > > > > I'm goin to the site right now :)
> > > > > Ryan
> > > >
> > > >
> > > > No offense taken. I've been procrastinating long enough.
> > > >
> > > > -John Van
|
|
Message has 1 Reply:
 | | Re: Hose spreadsheet now available
|
| Nope. I still didn't get it. Are you sure it was included in the zip? Did nayone else who downloaded it get the readme file?? All I got was: hoser.txt and hoser.xls Ryan ***...*** REPLY SEPARATOR ***...*** (...) (27 years ago, 15-Apr-99, to lugnet.cad)
|
Message is in Reply To:
| | Re: Hose spreadsheet now available
|
| No, I mean the hsreadme.txt that was included in the zip file. I'd rather you try to make a hose based on those instructions so that I can see if more/different explaination is neccessary. -John Van SCOTT R DENNETT wrote in message (...) (27 years ago, 15-Apr-99, to lugnet.cad)
|
17 Messages in This Thread:
 
  
- Entire Thread on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
This Message and its Replies on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
|
|
|
|
