 | | Re: SVG renders possible?
|
|
(...) Add the following to LDView's command line: -GL2PSAllowed=1 Alternatively, run regedit, browse into the HKEY_CURRENT_USER\So...are\Travis Cobbs\LDView key, then create a new DWORD value there named GL2PSAllowed, and set it to 1. Once you do (...) (14 years ago, 25-May-11, to lugnet.cad.dev)
|
| |
| | Re: My attempts to get a vector line drawing
|
|
(...) (FUT lugnet.cad.dev) I draw everything but the edge lines with glColorMask() set to all false. This updates the depth buffer, but doesn't update the color buffer. Edge lines are drawn with a standard glColorMask(). --Travis (14 years ago, 25-May-11, to lugnet.cad, FTX)
|
| |
| | Re: SVG renders possible?
|
|
(...) How would I go about enabling this experimental feature? I'd like to try it out on one of my line drawings. Eric Albrecht (14 years ago, 24-May-11, to lugnet.cad.dev)
|
| |
| | Re: MLCad Group
|
|
(...) Hi Tore, Jaco has documented it in the LPub4 web page. The idea is that buffer exchange is most commonly used for removing parts from the previous step, but what if you want to remove something from an older step? You could use buffer (...) (14 years ago, 24-May-11, to lugnet.cad.dev)
|
| |
| | Re: Beveled flex tubing [DAT]
|
|
(...) Great! Note that it may be easier to use slant instead of stretch/rotate. It is a bit more difficult to figure out at the beginning, but it avoids calculations and gives simpler coefficients. Here is the result, applied to your file: 0 (...) (14 years ago, 24-May-11, to lugnet.cad)
|
| |
| | Re: Beveled flex tubing [DAT]
|
|
(...) That did it! Here's the part I needed... thanks again!!!! 0 ~Technic Flex-System Hose 45 bevel End 0 Name: 76_bevel3.dat 0 Author: Lar with hints from Philo 0 ROTATION CENTER 0 0 0 1 "Custom" 0 ROTATION CONFIG 0 0 0 WRITE Inner cylinder (...) (14 years ago, 24-May-11, to lugnet.cad)
|
| |
| | Re: Beveled flex tubing
|
|
(...) Google translate does a pretty fair job, actually, enough to suss out most of what is being said... Manfred's section of notes in the part authoring "tutorial" (URL) is also helpful (URL) wasn't aware that there was a sliced cylinder primitive (...) (14 years ago, 24-May-11, to lugnet.cad)
|
| |
| | Re: My attempts to get a vector line drawing
|
|
(...) Hey, this is interesting. Is it actually just drawing the visible lines in some final rendering stage? Or is there more going on there with the Stencil and/or Depth buffer? (14 years ago, 24-May-11, to lugnet.cad, FTX)
|
| |
| | Re: Beveled flex tubing
|
|
OK, I think what you miss is the 4-4cyls.dat primitive, add it to a regular 4-4cyli and you basically have what you need. For the tip, you need a slanted primitive (ring and edges). There is a tutorial (unfortunately in French) here (URL) , (...) (14 years ago, 24-May-11, to lugnet.cad)
|
| |
| | Re: Beveled flex tubing
|
|
(...) I was looking at trying to use your cutting tool, actually,.. stretch a 4-4cyli.dat to a long enough length (somehow?) and then just use a big quad tilted to 45 degrees as the "blade". But I can't quite suss out how to do it, being somewhat (...) (14 years ago, 24-May-11, to lugnet.cad)
|
