Special:
|
[DAT] (requires LDraw-compatible viewer)
|
Subject:
|
Re: Beveled flex tubing
|
Newsgroups:
|
lugnet.cad
|
Date:
|
Tue, 24 May 2011 17:20:44 GMT
|
Viewed:
|
19194 times
|
| |
![Post a public reply to this message](/news/icon-reply.gif) | |
In lugnet.cad, Larry Pieniazek wrote:
> In lugnet.cad, Philippe Hurbain wrote:
> > OK, I think what you miss is the 4-4cyls.dat primitive, add it to a regular
> > 4-4cyli and you basically have what you need. For the tip, you need a slanted
> > primitive (ring and edges).
That did it! Here's the part I needed... thanks again!!!!
0 ~Technic Flex-System Hose 45 bevel End
0 Name: 76_bevel3.dat
0 Author: Lar with hints from Philo
0 ROTATION CENTER 0 0 0 1 "Custom"
0 ROTATION CONFIG 0 0
0 WRITE Inner cylinder (unbeveled part to bring inner bevel to same endpoint )
1 16 0 0 0 2 0 0 0 2 0 0 0 2 4-4cyli.dat
0 STEP
0 WRITE Inner and outer bevels
1 16 0 0 0 -4 0 0 0 4 0 0 0 -4 4-4cyls.dat
1 16 0 2 0 -2 0 0 0 2 0 0 0 -2 4-4cyls.dat
0 STEP
0 WRITE Face ring, stretched 1.414:1 and rotated 45
1 16 0 4 0 0 -0.707106 2 0 0.707107 2 -2 0 0 4-4ring1.dat
0 STEP
0 WRITE Edge lines for face ring, stretched 1.414:1 and rotated 45
1 24 0 4 0 0 -0.707106 2 0 0.707107 2 -2 0 0 4-4edge.dat
1 24 0 4 0 0 -0.707106 4 0 0.707107 4 -4 0 0 4-4edge.dat
0
|
|
Message has 1 Reply: ![](/news/x.gif) | | Re: Beveled flex tubing [DAT]
|
| (...) Great! Note that it may be easier to use slant instead of stretch/rotate. It is a bit more difficult to figure out at the beginning, but it avoids calculations and gives simpler coefficients. Here is the result, applied to your file: 0 (...) (13 years ago, 24-May-11, to lugnet.cad)
|
Message is in Reply To:
![](/news/x.gif) | | Re: Beveled flex tubing
|
| (...) Google translate does a pretty fair job, actually, enough to suss out most of what is being said... Manfred's section of notes in the part authoring "tutorial" (URL) is also helpful (URL) wasn't aware that there was a sliced cylinder primitive (...) (13 years ago, 24-May-11, to lugnet.cad)
|
9 Messages in This Thread: ![Beveled flex tubing -Larry Pieniazek (23-May-11 to lugnet.cad)](/news/x.gif) ![](/news/46.gif) ![Re: Beveled flex tubing -Timothy Gould (23-May-11 to lugnet.cad)](/news/x.gif) ![](/news/46.gif) ![Re: Beveled flex tubing -Ross Crawford (24-May-11 to lugnet.cad)](/news/x.gif) ![](/news/46.gif) ![Re: Beveled flex tubing -Philippe Hurbain (24-May-11 to lugnet.cad)](/news/x.gif) ![](/news/46.gif) ![Re: Beveled flex tubing -Larry Pieniazek (24-May-11 to lugnet.cad)](/news/x.gif) ![](/news/46.gif) ![Re: Beveled flex tubing -Philippe Hurbain (24-May-11 to lugnet.cad)](/news/x.gif) ![](/news/46.gif) ![Re: Beveled flex tubing -Larry Pieniazek (24-May-11 to lugnet.cad)](/news/x.gif) ![](/news/46.gif) ![You are here](/news/here.gif) ![](/news/46.gif) ![Re: Beveled flex tubing -Philippe Hurbain (24-May-11 to lugnet.cad)](/news/x.gif)
- Entire Thread on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
This Message and its Replies on One Page:
- Nested:
All | Brief | Compact | Dots
Linear:
All | Brief | Compact
|
|
|
|