 | | Re: Questions about LPub
|
|
(...) There are a couple of things that throw LPub off and I'm trying to figure out how to make it "do the right thing". You have: ROTSTEP part part part STEP ROTSTEP END This is equivalent to: part part part ROTSTEP ROTSTEP END LPub ignores STEP (...) (19 years ago, 28-May-05, to lugnet.cad)
|
| |
| | Re: Questions about LPub
|
|
(...) I got this one fixed: it was caused by the "0 ROTSTEP END" at the end of the subfile (actually a plain 0 STEP at the end also brings on this behaviour) Philo (19 years ago, 28-May-05, to lugnet.cad)
|
| |
| | ldraw part fro #32467
|
|
Does anyone have a .dat / ldraw file for part 32467 Yellow Electric Computer Speed as in set: (URL) (19 years ago, 28-May-05, to lugnet.cad)
|
| |
| | Re: Questions about LPub
|
|
Hello Kevin, (...) I have a similar problem: pack_callout: accumulated width too large but AFAIK it is not a recursive call problem... The mpd file is here (the problem occurs when generating layout 5) (URL) purpose of the callout (and tentative (...) (19 years ago, 28-May-05, to lugnet.cad)
|
| |
| | Re: LPub 2.3.0.7
|
|
In lugnet.cad, Philippe Hurbain wrote: <snip> (...) Fixed. Released. (...) Added. Not released. (...) Documentation made available. Kevin (19 years ago, 28-May-05, to lugnet.cad)
|
| |
| | Re: Questions about LPub
|
|
(...) Jacko, This is because hinge.ldr references itself in a LPUB PLI BEGIN SUB hinge.ldr. I removed the offending LPUB PLI BEGIN SUB/LPUB PLI END. I copied the parts listed in hinge.ldr to the places you used hinge.ldr. I then surrounded those (...) (19 years ago, 28-May-05, to lugnet.cad)
|
| |
| | Re: Questions about LPub [DAT]
|
|
(...) I found and fixed a bug in PLI. (...) It contains this: 0 Torso & arms 0 Name: torsoarms.ldr 0 Author: Jaco van der Molen 0 Unofficial Model 0 ROTATION CENTER 0 0 0 1 "Custom" 0 ROTATION CONFIG 0 0 0 LPUB PLI BEGIN SUB torsoarms.ldr 1 1 0 0 0 (...) (19 years ago, 28-May-05, to lugnet.cad)
|
| |
| | Re: Questions about LPub
|
|
OK. I am getting there :-) (...) This was a succes, though I do not have a pointer yet: (URL) further, I get an error: pack_callout: accumulated height too large And: layout_page: Failed to open file LPub\Layout\truck_0_05_co_0.png for reading Then, (...) (19 years ago, 27-May-05, to lugnet.cad)
|
| |
| | Re: Questions about LPub
|
|
How can I get something like this on the first page of the instructions? (URL) (19 years ago, 27-May-05, to lugnet.cad)
|
| |
| | Re: Questions about LPub
|
|
(...) I am getting this error: Cannot find user part image C:\LDRAW\MODELS\MISC...s_c.PNG_c. Did you create create construction images? What could be wrong? I have posted my MPD file on Brickshelf here: (URL) (19 years ago, 27-May-05, to lugnet.cad)
|
| |
| | Re: Questions about LPub
|
|
I had that problem until I installed an unknow version. If the helpfile is not found, perhaps a warning could be displayed? And while you're at it, perhaps a link to the file for download? "Help files not found. Download them here." Is it even (...) (19 years ago, 27-May-05, to lugnet.cad)
|
| |
| | Re: Questions about LPub
|
|
In lugnet.cad, Travis Cobbs wrote: <snip> (...) Yes, they are the same DATs that go through L3P. L3P leaves the steps in the POV file as comments. I then use those to determine what parts need to be grayed and which not. (...) Kevin (anyone notice (...) (19 years ago, 27-May-05, to lugnet.cad, FTX)
|
| |
| | Re: Questions about LPub
|
|
(...) LDView supports 24-bit extended colors (color numbers 0x02000000-0x03FFFFFF, see (URL) here>). Does LDGLite? If so, just specify the RGB color, instead of the LDraw color. If not, you could still do this for LDView, and use the 12-bit dither (...) (19 years ago, 27-May-05, to lugnet.cad, FTX)
|
| |
| | Re: Questions about LPub
|
|
(...) <snip> (...) Ooohhhhh, I like this last one. (...) Kevin (19 years ago, 27-May-05, to lugnet.cad)
|
| |
| | Re: Questions about LPub
|
|
(...) I'm not so sure about that quantizing bit. It may not be the best way, but I think the current beta version of ldglite could be controlled by lpub inserting a block of 0 COLOR macros at the beginning of each temp DAT file to dim the colors, (...) (19 years ago, 27-May-05, to lugnet.cad)
|
| |
| | Re: Questions about LPub
|
|
(...) Don, LPub modified the POV file creted by L3P to support previous part color scaling. Some amount of this could be done at the DAT stage, not the POV stage, but the color spectrum would be greatly quantized. Kevin (19 years ago, 27-May-05, to lugnet.cad)
|
| |
| | Re: Questions about LPub
|
|
(...) Is this an lpub issue, or something that should perhaps be added on the ldglite command line? How is this done with the l3p/pov renderer? Does lpub manipulate the intermediate files or the rendering programs? Just curious, Don (19 years ago, 27-May-05, to lugnet.cad)
|
| |
| | Re: LPub2.3.0.8 (was LPub 2.3.0.7)
|
|
(...) Got it this time! Thanks a lot for your efforts! Philo (19 years ago, 27-May-05, to lugnet.cad)
|
| |
| | Re: Questions about LPub
|
|
(...) Agreed, but this menu entry does nothing for me (most probably because the help file is not there ;o) Philo (19 years ago, 27-May-05, to lugnet.cad)
|
| |
| | Re: LPub2.3.0.8 (was LPub 2.3.0.7)
|
|
(...) Um...... Please re-get 2.3.0.8. (...) Kevin (19 years ago, 27-May-05, to lugnet.cad)
|
