 | | Re: wishin' on a star —David Laswell
|
| | | (...) The stud notches pretty much peg it as a 2x2. (...) I was able to figure them all out without any trouble, with only a few exceptions: 1. Double-ended clip plate (not sure why the other two variants weren't included). 4. 1x1 round tile. 6. (...) (20 years ago, 7-Jul-04, to lugnet.build, FTX)
|
| | | |
| | | | | Re: wishin' on a star —Larry Pieniazek
|
| | | | | (...) or something that fits on top of a 1x1 tile, if the scale is unclear. (20 years ago, 7-Jul-04, to lugnet.build, FTX)
|
| | | | | |
| | | | | | | Re: wishin' on a star —David Laswell
|
| | | | | | (...) You're thinking too hard and not looking at all of the evidence. It's the only part in the entire list that's upside-down, so there must be something significant to the bottom. You can also see the stud on the top peeking out, which is way (...) (20 years ago, 7-Jul-04, to lugnet.build, FTX)
|
| | | | | | |
| | | | | | | | Re: wishin' on a star —Larry Pieniazek
|
| | | | | | (...) I'd say, given that you posted such a detailed analysis of all the parts, with a running point by point commentary, that you're the one thinking too hard, but that's just me. I think a better approach than analysing in depth is to just ask the (...) (20 years ago, 7-Jul-04, to lugnet.build, FTX)
|
| | | | | | |
| | | | | | | | Re: wishin' on a star —Deborah Higdon
|
| | | | | | | (...) that was the point of the original post - entertainment. (...) much appreciated (...) again much appreciated (...) judgement is what human nature's all about. just content that someone looked at the pieces and got out of them what he/she (...) (20 years ago, 7-Jul-04, to lugnet.build, FTX)
|
| | | | | | | |
| | | | | | | | Re: wishin' on a star —David Laswell
|
| | | | | | (...) Not at all. Well, maybe with my second guess on #13, but that's a matter of the evidence (i.e. the original mlcad plate that it was modified from) being flawed. For everything else I clearly thought just hard enough, since I pegged them all. (...) (20 years ago, 7-Jul-04, to lugnet.build, FTX)
|
| | | | | | |
| | | | | Re: wishin' on a star —Deborah Higdon
|
| | | | | (...) perhaps i should have enclosed directions to my mocpages (URL) where all of the pieces are named, however the pieces are not visible on the page with the descriptions. (...) probably because i haven't lamented the lack of one yet. i only (...) (20 years ago, 7-Jul-04, to lugnet.build, FTX)
|
| | | | | |
| | | | | | | Re: wishin' on a star —David Laswell
|
| | | | | | | (...) Yeah, it does clear up a few questions...though the description of part #17 looks a bit mixed up. As I said earlier, the part you based it on is 2x2x1, not 2x2x2, and you listed it as being "without center stud", when you showed it without the (...) (20 years ago, 7-Jul-04, to lugnet.build, FTX)
|
| | | | | | | |
| | | | | | | Re: wishin' on a star —Mike Kollross
|
| | | | | | snippage (...) snippage I have a hack that does the same thing. This can be achieved using a lenghthwise 1x2 modified plate with 1 pin (jumper plate) and connect a headlight brick on top but connect it to the square hole on the back with the top (...) (20 years ago, 9-Jul-04, to lugnet.build, FTX)
|
| | | | | | |
| | | | | Re: wishin' on a star —David Laswell
|
| | | | (...) Whoops, meant to say "about 1/2-tile short of 2-brick height". (20 years ago, 7-Jul-04, to lugnet.build, FTX)
|
| | | | |
