 | | Re: Building pyramids. (Was: Announcing my newly completed website)
|
|
(URL) on there somewhere is a link to Paulo's dat2dxf converter. There is also a zip file containing a few sample conversions. I have yet to use the actual program....as the bricks I needed were there in the zip file....though I will be shortly. And (...) (26 years ago, 28-Oct-98, to lugnet.build)
|
| |
| | Re: Building pyramids. (Was: Announcing my newly completed website)
|
|
(...) where can I get the above mentioned DXF converter? -- ___...___ L. M. Lloyd lee@advfilms.com SGI Animator ADV Films USA ___...___ (26 years ago, 27-Oct-98, to lugnet.build)
|
| |
| | Re: Building pyramids. (Was: Announcing my newly completed website)
|
|
(...) Oba! I am glad someone is using it! (...) Paulo (26 years ago, 27-Oct-98, to lugnet.build)
|
| |
| | Re: Building pyramids. (Was: Announcing my newly completed website)
|
|
Certainly. They both demonstrate studs, as opposed to actual bricks. I was very tired when I wrote it..... The picture I had hoped to demonstrate how bricks on different levels should relate to each other. I think what would be best might be a (...) (26 years ago, 27-Oct-98, to lugnet.build)
|
| |
| | Building pyramids. (Was: Announcing my newly completed website)
|
|
Richard, I wonder if you could clear this up a little bit? (...) I understand how this makes a pyramid. (...) I don't understand how this makes a pyramid. Does the pyramid rise with a less steep angle now? Are these three lines one vertical section? (...) (26 years ago, 27-Oct-98, to lugnet.build)
|
| |
| | Re: Announcing my newly completed website
|
|
Actually, I had decided to go very big on a pyramid, which I finished last weekend. After building a pyramid on a 48x48 baseplate (nice sounding drum, by the way), went for an 80-stud wide pyramid, built upon a 48x48 surrounded by a ring of 16x32's. (...) (26 years ago, 26-Oct-98, to lugnet.build)
|
| |
| | Re: Identify this pneumatic piece
|
|
Matthew Bates wrote in message ... (...) Which leads me to think that the pneumatic switch is different now (...) Actually, no. The crucial difference between the old and the new pneumatics system is that the old one used both pressure and suction, (...) (26 years ago, 26-Oct-98, to lugnet.build)
|
| |
| | Re: Identify this pneumatic piece
|
|
(...) That's the piece! Except mine's black. Matt (26 years ago, 26-Oct-98, to lugnet.build)
|
| |
| | Re: Rocker-boogie suspension model
|
|
Hey, that is one cool model. It took me a while to figure out how to build from the instructions included, but it is worth it! If there is interest, I could take pictures of the rocker-boogie with my digital camera and post pictures on my web page. (...) (26 years ago, 23-Oct-98, to lugnet.build, lugnet.robotics)
|
| |
| | Re: Announcing my newly completed website
|
|
Louise Belles wrote in message ... (...) remove (...) which (...) that (...) spots. (...) that (...) been (...) great (...) a (...) I hear you, one of my ex's, Donna (sister of RTLer Denny who doesn't post much these days) is a Structural engineer (...) (26 years ago, 23-Oct-98, to lugnet.build, lugnet.general)
|
| |
| | Re: Announcing my newly completed website
|
|
(...) I resolved a building difficulty which would also work to stabalize a pyramid. I wanted the roof of my train station to be durable enough to remove in one piece. I reinforced the underside of the roof with narrow plates which spanned the (...) (26 years ago, 23-Oct-98, to lugnet.build, lugnet.general)
|
| |
| | Re: Identify this pneumatic piece
|
|
Hopefully this will clear up the subject of exactly what piece we are talking about. The one I am trying to describe can be found in set 8040. I have a scan of one page in the instructions which illustrates the piece I have in mind. (URL) this piece (...) (26 years ago, 23-Oct-98, to lugnet.build)
|
| |
| | Re: Identify this pneumatic piece
|
|
I think it is a dacta angle sensor. Selçuk Matthew Bates wrote in message ... (...) now (...) has (...) it, (...) round, (...) a (...) (26 years ago, 23-Oct-98, to lugnet.build)
|
| |
| | Re: Identify this pneumatic piece
|
|
(...) After seeing the diagram in that old Technic set, it makes more sense that this is a valve block, without valves somewhere the piston would just slide back down. Which leads me to think that the pneumatic switch is different now and has (...) (26 years ago, 23-Oct-98, to lugnet.build)
|
| |
| | Re: Identify this pneumatic piece
|
|
(...) Well, okay, I never opened one up. But if you think about how it operates - it's pretty basic. (26 years ago, 23-Oct-98, to lugnet.build)
|
| |
| | Re: Announcing my newly completed website
|
|
(...) I'd be interested. It's too long a lead time to launch it, but it's not too early to think about it, and decide how it will work, and what organization is needed for it. Just to be ready. Steve (26 years ago, 23-Oct-98, to lugnet.build)
|
| |
| | Re: Identify this pneumatic piece
|
|
(...) It is? I always thought there were some kind of valves inside it which split the air into different nozzles depending on the air flow direction. But then again, I only had one as a kid, and never did any experiments with it. Fredrik (26 years ago, 23-Oct-98, to lugnet.build)
|
| |
| | Re: Announcing my newly completed website
|
|
Steve Bliss wrote in message <362f3a45.9161533@lu...et.com>... (...) Thanks, Steve. If I ever can beat the demon Diablo addiction I have developed since buying my new computer, I will finish the model and get some pics taken. Hmm, maybe it is time (...) (26 years ago, 22-Oct-98, to lugnet.build)
|
| |
| | Re: Identify this pneumatic piece
|
|
> I acquired a bunch of LEGO recently, mostly Technic, and one piece > I haven't seen before. It's basically a black 2x4 brick with three > ports for attaching air hoses. What's it for and what sets did it > come in? It seems like it might have (...) (26 years ago, 22-Oct-98, to lugnet.build)
|
| |
| | Re: Identify this pneumatic piece
|
|
Darn text wrapping gets me every time! (...) ======== Posted via the LUGNET discussion group web interface ======== (URL) Search, Read, Post, or Watch Traffic (26 years ago, 22-Oct-98, to lugnet.build)
|
