 | | Re: Bogie design (coupler)
|
|
Even better: by using this part: Technic Rotor 2 Blade with 2 Studs [LDrawPart 2711:7] you can achieve the desired 2,5 stud offset, by putting two Plates 1 x 1 Round under the part (one in the hole at one of the ends and the other right next to it) (...) (21 years ago, 28-Nov-03, to lugnet.trains, FTX)
|
| |
| | Re: Bogie design (coupler)
|
|
(...) You mean like (URL), very clever, you've done this before, haven't you! I wondered about the strength at first but the fact that the stud on top of the "Technic Rotor 2 Blade with 2 Studs" meshes with the bottom of the bogie plate just adds (...) (21 years ago, 28-Nov-03, to lugnet.trains, FTX)
|
| |
| | Re: Bogie design (coupler)
|
|
(...) Tim, I like these little renderings you've been working up VERY much. I hope I can convince you to make up an FTX page with all of them in it, (which I would then link to from the header) (1) because it's good stuff, good stuff indeed. The use (...) (21 years ago, 28-Nov-03, to lugnet.trains, FTX)
|
| |
| | Re: Bogie design (coupler)
|
|
(...) I got the impression that that was what he was aming for, I wasn't certain that it would work tho as the coupling could just swing any which way. You could mount the coupling straight on the rotor arm but it wouldn't be at Lego™ standard (...) (21 years ago, 28-Nov-03, to lugnet.trains, FTX)
|
| |
| | Re: Bogie design (coupler)
|
|
(...) Actually, not. We Europeans don't mind buffers :-) But the problem intrigued me, and I like to puzzle out technical solutions, so I gave it a try. (...) He wanted 2,5 stud offset. Because the magnets swivel around their horizontal axes they (...) (21 years ago, 29-Nov-03, to lugnet.trains, FTX)
|
| |
| | Re: Bogie design (coupler)
|
|
Tim David <talltim@hotmail.com> wrote in message news:Hp3116.1Cp@lugnet.com... (...) 1 (...) right (...) between (...) Train (...) stud (...) the (...) 2 (...) that (...) I think it is time that I give my point of view here. I made some tests using (...) (21 years ago, 1-Dec-03, to lugnet.trains)
|
| |
| | Re: Bogie design (coupler)
|
|
Instead of a bogie plate you can always use a Tile, Modified 2 x 2 with Pin [LDrawPart 2460:0] This gives you more flexibility with how you attache beams etc. you alos don't have to have the pivot poit in the centre of the bogie. Tim (21 years ago, 1-Dec-03, to lugnet.trains, FTX)
|
| |
| | Re: Bogie design (coupler)
|
|
(...) Yep. I actually use this in MTW-1003 because I want the wobble this gives you (it's a bit taller of a pin than a normal bogie plate's pin which fits into two plates worth of space, this is a full brick thick or 2.5 plates) but the flexibility (...) (21 years ago, 1-Dec-03, to lugnet.trains, FTX)
|
| |
| | Re: Bogie design (coupler)
|
|
(...) Maybe you could lengthen it with part #2905: Technic Triangle, if you don't mind that somewhere inside or under your nose it's sticking out sideways [LDrawPart 2905:7] (...) I have absolutely no clue what you're talking about here, we probably (...) (21 years ago, 2-Dec-03, to lugnet.trains, FTX)
|
| |
| | Re: Bogie design (coupler)
|
|
(...) Ah, suddenly I do understand what you ment here, but unfortunately this would not fit. A 4263 Technic Plate 1 x 4 with Holes under the 2711 Technic Rotor 2 Blade with 2 Studs (with one hole and 2 studs overlap, and only the other hole (...) (21 years ago, 3-Dec-03, to lugnet.trains)
|
| |
| | Re: Bogie design (coupler)
|
|
M. Moolhuysen <moom@NOSPAM-chello.nl> wrote in message news:HpCB4D.F1D@lugnet.com... (...) the (...) would (...) Rotor 2 (...) hole (...) Plate (...) the (...) as the (...) around (...) I am sure there is a way around that problem. I just need to (...) (21 years ago, 4-Dec-03, to lugnet.trains)
|
