 | | Re: Low-tech & low cost controls
|
|
(...) There's also a way to use only one controller to run at least two trains, but both are at the same speed. While probably not what Pedro's looking for, it leads into more complicated electrical block control. Here's a folder with an example: (...) (22 years ago, 17-May-02, to lugnet.trains)
|
| |
| | Re: Low-tech & low cost controls
|
|
(...) Funny you should mention. I just this month gave a 10 minute talk to my train club on the merits of electrical block control. Perhaps I can help out. (...) True. (...) True. (...) Additional feeder wires every 25-100 ft or so should reduce the (...) (22 years ago, 17-May-02, to lugnet.trains)
|
| |
| | Re: Advanced Design Train Roundhouse
|
|
(...) That's true. I'd recommend 48 if LUCNY had real estate right now to display Wayne's design, but we don't. I think starting with a 32 would be prototypical and fit our table design. (...) Yes, that's also true. Steamtown's table is large, but (...) (22 years ago, 17-May-02, to lugnet.org.us.lucny, lugnet.trains)
|
| |
| | Re: Advanced Design Train Roundhouse
|
|
(...) I would go 48 if I could. But I should hasten to point out that it is prototypical for engines not to fit on the turntable in US practice. It happened fairly frequently. The most common solution was to service the engine in the stall that was (...) (22 years ago, 17-May-02, to lugnet.org.us.lucny, lugnet.trains)
|
| |
| | Re: Advanced Design Train Roundhouse
|
|
(...) it, just the main drive. It's a fairly standard drive with the motor in the house. Another note, Steve's setup is very modular. Although it makes up a fixed configuration (that spans at least a 5x8 foot area when the yard is included), it's (...) (22 years ago, 17-May-02, to lugnet.org.us.lucny, lugnet.trains)
|
| |
| | Re: Advanced Design Train Roundhouse
|
|
(...) Steve Ringe, our 8 Wide King. I will see if I can get him to reply, he usually is too busy building to post much. (...) The turntable sequences by using mindstorms touch sensors to detect when the table is "close" to the approach track and (...) (22 years ago, 17-May-02, to lugnet.org.us.lucny, lugnet.trains)
|
| |
| | Re: Work in progress, an EMU
|
|
(...) The vestibule plates are quite beefy on some MU's (eg 156 sprinters). Yours doesn't look bad at all as it stands but you should try the snot technique or something similar, I'm sure it would look even better. There are techniques that the (...) (22 years ago, 15-May-02, to lugnet.loc.uk, lugnet.trains)
|
| |
| | Re: New Builder Profile on LEGO.com/trains-- Ross Neal
|
|
(...) Congrats to Ross and his proud father! If I read the inteview I still cannot imagine a 12-years old sitting in front of Max. Indeed, very smart answers.... (...) Ross is a friend of mine! Big steam engines drive wheels - exactely what I ask (...) (22 years ago, 17-May-02, to lugnet.general, lugnet.trains)
|
| |
| | Re: Advanced Design Train Roundhouse
|
|
(...) Thanks for sharing these ideas: I have had the motor outside the turntable and had a long connecting axle hidden underneath the turntables visible floor. But in the end this lead to my 5 bricks high solution, that I dislike. In a beta-version (...) (22 years ago, 17-May-02, to lugnet.org.us.lucny, lugnet.trains)
|
| |
| | Re: New Builder Profile on LEGO.com/trains-- Ross Neal
|
|
(...) Na... he'd immediately switch to 10 wide because it would be "more realistic" or some similar folderol, you can be sure of that! :-) (22 years ago, 17-May-02, to lugnet.general, lugnet.trains)
|
