 | | Pneumatic T-cross math-rule
|
|
Hi! I'm onto this rather big pneumatics project where I have several cylinders per switch and I found that if the numbers of cylinders used is 'Y' and the number of T-crosses is 'X' then this is true (if you use but one switch to control the whole (...) (25 years ago, 21-Nov-00, to lugnet.technic)
|
| |
| | Re: where can I get the mag wheel master???????
|
|
(...) If it's the wheels you're after, they can also be found in 5219 Wheel Pack: (URL) pack has two of the narrow front wheel from the 8417. Fredrik (25 years ago, 21-Nov-00, to lugnet.technic)
|
| |
| | Re: Another Technic Creation
|
|
(...) As a child, I only had one of the large, bulky 4,5V motor with black housing and built in gear. I actually found it pretty useful, but then again I never put my hands on any other kinds om motors. The most useful feature of the motor was the (...) (25 years ago, 21-Nov-00, to lugnet.technic)
|
| |
| | Re: Another Technic Creation
|
|
Well, I've been thinking about this, and I think it's possible to do with an arrangement like the valve gear on your everyday steam engine. This would allow it to be changed with the wheels in any position. Implementing this, however, is not trivial (...) (25 years ago, 21-Nov-00, to lugnet.technic)
|
| |
| | where can I get the mag wheel master???????
|
|
I live in canada and was wondering if there are any outlet stores or anything where I can get the mag wheel master. i recently bought the circuit shock racer off of my friend at school but I'm looking to start a website with technic MOC motorcycles (...) (25 years ago, 21-Nov-00, to lugnet.technic)
|
| |
| | Re: Another Technic Creation
|
|
(...) I came to exactly the same conclusion. I hope we are both correct! (...) A pure mechanical solution, which would work with 4 wheel steered vehicles, with each axle being steered to the same (or opposite) angle such as the one you describe, is (...) (25 years ago, 21-Nov-00, to lugnet.technic)
|
| |
| | Re: Another Technic Creation
|
|
Jennifer Clark wrote: [] (...) I've been toying with this -- mostly on paper -- as well, in attempt to convert my 8448 to four-wheel dual-mode steering. Unfortunately, as far as I can tell, the only way to do it its to only switch modes when the (...) (25 years ago, 20-Nov-00, to lugnet.technic)
|
| |
| | Re: Another Technic Creation
|
|
(...) a (...) better, (...) A _mere_ 9V? I ran one up to 54V, for short periods of time. However, the real answer is to use a hefty 12V motor. I have a 12V can motor (it might even be a 24V job, in fact) that runs quite happy with _anything_ you (...) (25 years ago, 20-Nov-00, to lugnet.technic)
|
| |
| | Re: Another Technic Creation
|
|
(...) I remember this too, and also remembering building the thing and wondering why they were closing off one of the gears - they did it with a 1x1 plate if I remember correctly? I think it was because the engine went amazingly fast in the lowest (...) (25 years ago, 20-Nov-00, to lugnet.technic)
|
| |
| | Re: Another Technic Creation
|
|
(...) I still count the stuff out of the box - if I don't, them I usually miss something out at some point ;-) It's funny you mention the axle thing by the way, someone was watching me build recently and was amazed I could do the same thing just by (...) (25 years ago, 20-Nov-00, to lugnet.technic)
|
