 | | RE: Suspension —Bram Lambrecht
|
| | | (...) No, but almost as round as an LDraw cylinder :) It's 12 sided, built with a ring of <part: 4590> 1x4 offset plates. It's about 6 studs wide where it's in contact with the ground and 8 studs in the center. I expect it'll work best on carpet. (...) (24 years ago, 10-Aug-00, to lugnet.technic, lugnet.build)
|
| | | |
| | | | | Re: Suspension —Fredrik Glöckner
|
| | | | (...) That sounds fun! I expect that we will see LDraw'n images shortly... ;-) (...) But how are you going to connect your custom wheels to the 8880 suspension? It only supports the native 8880 wheels, unfortunately. (...) Yep, that works quite (...) (24 years ago, 10-Aug-00, to lugnet.technic, lugnet.build)
|
| | | | |
| | | | | | RE: Suspension —Bram Lambrecht
|
| | | | (...) I hope it works :) I've built two wheels with suspension now, so I'll try to get it motorized and then add the rest of the frame, the articulation, and the other wheels. (...) I'm not ;) Instead I built a somewhat similar system: basically two (...) (24 years ago, 10-Aug-00, to lugnet.technic, lugnet.build)
|
| | | | |
| | | | | | Re: Suspension —Bram Lambrecht
|
| | | | | (...) I attached the wheels to the motor, and built most of the rear engine compartment, including exterior body and fiber-optic engine. The suspension is quite stiff. Thanks to a worm gear, the vehicle moves slowly but steadily. The fact that the (...) (24 years ago, 11-Aug-00, to lugnet.technic, lugnet.build)
|
| | | | | |
| | | | | | | Re: Suspension —Jennifer Clark
|
| | | | | | | (...) I'm a bit of a Johnny come lately in this thread, but I did attempt something similar to this a wee while ago. The idea was to build a 6 wheel drive Moxy style articulated dump truck, the chassis for which sounds not dissimilar to your (...) (24 years ago, 11-Aug-00, to lugnet.technic, lugnet.build)
|
| | | | | | | |
| | | | | | | Re: Suspension —Bram Lambrecht
|
| | | | | | Update on the rover: The rear end is complete, including the articulating section which is driven by a micromotor. I tested it by adding a couple big wheels to the front, and as long as the vehicle is moving forward, it turns quite nicely, thanks to (...) (24 years ago, 12-Aug-00, to lugnet.technic, lugnet.build)
|
| | | | | | |
| | | | | | Re: Suspension —Fredrik Glöckner
|
| | | | (...) Ah, yes! A custom made independent suspension, much like the one on 8448 or 8865. This approach will need no less than four universal joints. I think that it prevents the width of the vehicle from being narrow, so I've never used this approach (...) (24 years ago, 11-Aug-00, to lugnet.technic, lugnet.build)
|
| | | | |
| | | | | | RE: Suspension —Bram Lambrecht
|
| | | | (...) Yeah, in this case, wider = more impressive. (...) I've decided to make the model 2 wheel drive because I want room for some interior details. Time to go work on the model :) --Bram Bram Lambrecht BXL34@po.cwru.edu (URL) (24 years ago, 12-Aug-00, to lugnet.technic, lugnet.build)
|
| | | | |
