 | | Re: How to make a perfect octagon or hexagon?
|
|
(...) Try approaching it in steps. Can you make an equilateral triangle out of Technic beams? Don't worry about making the angles rigid, just make a structure with three equal-length sides, connected near the corners (connected with something that (...) (17 years ago, 10-Dec-07, to lugnet.technic)
|
| |
| | Re: How to make a perfect octagon or hexagon?
|
|
(...) The tri-blade is great for hexagons.... (URL) (17 years ago, 10-Dec-07, to lugnet.technic, FTX)
|
| |
| | Re: How to make a perfect octagon or hexagon?
|
|
(...) It would appear that they're approximately 126.8698976 degrees. That's from approximating some angles and noticing that what I think they were trying to do was to create the geometry such that a 3-4-5 right triangle was possible. DaveE (17 years ago, 10-Dec-07, to lugnet.technic, FTX)
|
| |
| | Re: How to make a perfect octagon or hexagon?
|
|
Your best bet would be the #4 angle connector, its a 135 degree angle. (17 years ago, 10-Dec-07, to lugnet.technic)
|
| |
| | How to make a perfect octagon or hexagon?
|
|
I'm trying to make a largish (20 cm across or so) octagon or hexagon out of technic parts. I thought this would be easy, because I believed that the bent technic beams (e.g. (URL) 32348>) had a 135-degree angle, or at least some angle that would (...) (17 years ago, 10-Dec-07, to lugnet.technic, FTX)
|
| |
| | Re: 951/856 bulldozer instructions question
|
|
Hello Jonathan, You have to check the pictures on the box to see how the blade is mounted to the bulldozer... Greetings Maico Arts Jonathan Wilson schreef: (...) (17 years ago, 8-Dec-07, to lugnet.technic)
|
| |
| | Re: Technicopedia
|
|
Update ====== Sets from 1981 have been listed including 8844, 8845, 8846, 8848, and 8859. blakbird (17 years ago, 8-Dec-07, to lugnet.technic, FTX)
|
| |
| | 951/856 bulldozer instructions question
|
|
Both the 951 instructions and the 856 instructions on Peeron show a bulldozer on the front page with a flat blade. However, the instructions show how to build a front end loader with no instructions for the bulldozer at all. Anyone know whats going (...) (17 years ago, 7-Dec-07, to lugnet.technic)
|
| |
| | Re: Building a realistic working road grader from Technic LEGO parts.
|
|
"Nathan Bell" <Radarbell@hotmail.com> wrote in message news:Jsn2Jz.7nD@lugnet.com... (...) Another two pneumatic cylinders, and I think you would've had the steering like a real grader does. I've seen few other models with that degree of steering (...) (17 years ago, 7-Dec-07, to lugnet.technic)
|
| |
| | Re: Building a realistic working road grader from Technic LEGO parts.
|
|
(...) Clarification: the blade design in the pictures works but my modification did not work- therefore the overall blade range remains about 45 degrees. (17 years ago, 6-Dec-07, to lugnet.technic)
|
| |
| | Re: Building a realistic working road grader from Technic LEGO parts.
|
|
(...) I did a large technic road grader in 2006, and although the steering works, it does not work exactly like the real thing. I tried to modify it to make the blade rotate further, but it did not work and the design in the pictures is finished. (...) (17 years ago, 6-Dec-07, to lugnet.technic)
|
| |
| | Re: Building a realistic working road grader from Technic LEGO parts.
|
|
(...) Have you thought about using pneumatics for the front end? Are you planning on a newer style machine? Old motor graders had linkage and drive shafts to run everything. Modern machines are all hydraulic and use hydrostatic front wheel drive. I (...) (17 years ago, 2-Dec-07, to lugnet.technic)
|
| |
| | Building a realistic working road grader from Technic LEGO parts.
|
|
I've been looking at how to do a properly done, realistic road grader for some time now, from Technic LEGO, and I've become stuck trying to properly emulate a realistic design for the front steering. As anyone who's seen a road grader knows, they (...) (17 years ago, 1-Dec-07, to lugnet.technic)
|
| |
| | Re: Killough platform with power functions
|
|
(...) Done - thanks! (17 years ago, 1-Dec-07, to lugnet.technic, FTX)
|
| |
| | Re: Killough platform with power functions
|
|
(...) Thanks a lot, Alexander! Now I have to find enough ballon wheels... or substitute Rama wheels ;o) Two little remarks about the mpd: The "whole" model should be the first in the MPD (Multipart > Model Sequence) You can add all PF parts that I (...) (17 years ago, 30-Nov-07, to lugnet.technic, FTX)
|
| |
| | Re: Killough platform with power functions
|
|
(...) Here are some building instructions (or at least an MLCad file). The PF parts are not shown, but it should be clear where they go: (URL) For anyone planning to build one, there is a warning: the way the wheels are put together may cause some (...) (17 years ago, 30-Nov-07, to lugnet.technic, FTX)
|
| |
| | New MOC: Cowans Sheldon 76T Rail Crane with Power Functions - photos
|
|
Here are the photos of my new Rail Crane with Power Functions: (URL) It's an 8mm scale model of a Cowans Sheldon 76T crane. Some details still to finish - I want to make sure it passes the scale load lifting test first. The scale load will be 6 full (...) (17 years ago, 28-Nov-07, to lugnet.trains, lugnet.technic, lugnet.announce.moc, lugnet.loc.uk, lugnet.build, FTX) !
|
| |
| | Re: Killough platform with power functions
|
|
Thanks for the videos and even more for the detailed and chear instructions! Coming up with this complex geartrain must have been quite tough ;o) Philo (17 years ago, 25-Nov-07, to lugnet.technic, FTX)
|
| |
| | Re: Killough platform with power functions
|
|
(...) No - the mechanism with the differentials does precisely this conversion for you! As you say, there is one IR channel for each motor. I am controlling it using this: (URL) The joystick on the left (inspired by this one (URL) from Mark Bellis) (...) (17 years ago, 24-Nov-07, to lugnet.technic, FTX)
|
| |
| | Re: Killough platform with power functions
|
|
(...) Looks like the tricky gear train handles a lot of it (URL) (17 years ago, 24-Nov-07, to lugnet.technic, FTX)
|
