To LUGNET HomepageTo LUGNET News HomepageTo LUGNET Guide Homepage
 Help on Searching
 
Post new message to lugnet.technicOpen lugnet.technic in your NNTP NewsreaderTo LUGNET News Traffic PageSign In (Members)
 Technic / 15478 (-10)
  Re: What's the difference?
 
(...) Yeah I suppose it would be, because you would have two different sets of gears that could both be changed. So in that way they'd be the same. The trick is to not duplicate ratio's because that's a waste. (18 years ago, 22-Dec-06, to lugnet.technic)
 
  Re: What's the difference?
 
(...) Is it something like the front and rear sprockets of a 10+ speed bike? I know there are frequently duplications of gear ratios there. (18 years ago, 22-Dec-06, to lugnet.technic)
 
  Re: What's the difference?
 
(...) That makes a lot of sense. The configurations I was coming up with in my head, tended to duplicate ratio's I already had. Steve (18 years ago, 21-Dec-06, to lugnet.technic)
 
  Re: What's the difference?
 
(...) I don't know any details about splitters, but if the difference in ratio of the 2 gears in the splitter is smaller than the difference between any of the standard gears, then it would create ratios between the standard gears as per Glen's (...) (18 years ago, 21-Dec-06, to lugnet.technic)
 
  Re: What's the difference?
 
(...) I've read all the replies and they seem to contradict each other, so I think I'll further define my question. If the splitter is an add on in front of the gear box how does it's internal mechanism give a ratio half way in between the gears. (18 years ago, 21-Dec-06, to lugnet.technic)
 
  Re: What's the difference?
 
Hello Bob, For as far as I can tell this is the line up: motor - clutch - splitter - gearbox - range change - cardan axle - driven axles Greetings Maico Arts Bob Fay schreef: (...) (18 years ago, 20-Dec-06, to lugnet.technic)
 
  Re: What's the difference?
 
(...) Hey Steve, I think the best way that I can describe the difference is by explaining how the gear shift on a Semi works...I have this knowledge.. I drive one! Hmmm...imagine a four speed standard transmission on a car.. neutral would be in the (...) (18 years ago, 21-Dec-06, to lugnet.technic)
 
  Re: What's the difference?
 
"Maico Arts" <lego@t-hok.nl> wrote in message news:JADAwy.296@lugnet.com... (...) This "splitter" may well occur in the differential. When the lever on the shifter is changed the differential shifts gears giving a lower or higher ratio to the (...) (18 years ago, 18-Dec-06, to lugnet.technic)
 
  Re: What's the difference?
 
Hello Steve, I would explain it like this: A gearbox with 4 gears forward plus 1 reverse with range change will give 4 lower gears and 4 upper gears, thus giving 8 gears forward. The splitter makes it possible to split these 8 gears when the truck (...) (18 years ago, 16-Dec-06, to lugnet.technic)
 
  What's the difference?
 
Between a splitter and a range change on a truck gearbox? I know what the difference is functionally, what I want to know is the mechanical difference. I've tried Google without much luck. Thanks. Steve (18 years ago, 15-Dec-06, to lugnet.technic)


Next Page:  5 more | 10 more | 20 more

Redisplay Messages:  All | Compact

©2005 LUGNET. All rights reserved. - hosted by steinbruch.info GbR