 | | Re: What's the difference? —Robert G Fay
|
| | | "Maico Arts" <lego@t-hok.nl> wrote in message news:JADAwy.296@lugnet.com... (...) This "splitter" may well occur in the differential. When the lever on the shifter is changed the differential shifts gears giving a lower or higher ratio to the (...) (18 years ago, 18-Dec-06, to lugnet.technic)
|
| | | |
| | | | | Re: What's the difference? —Maico Arts
|
| | | | Hello Bob, For as far as I can tell this is the line up: motor - clutch - splitter - gearbox - range change - cardan axle - driven axles Greetings Maico Arts Bob Fay schreef: (...) (18 years ago, 20-Dec-06, to lugnet.technic)
|
| | | | |
| | | | | | Re: What's the difference? —Steve Lane
|
| | | | (...) I've read all the replies and they seem to contradict each other, so I think I'll further define my question. If the splitter is an add on in front of the gear box how does it's internal mechanism give a ratio half way in between the gears. (18 years ago, 21-Dec-06, to lugnet.technic)
|
| | | | |
| | | | | | Re: What's the difference? —Ross Crawford
|
| | | | (...) I don't know any details about splitters, but if the difference in ratio of the 2 gears in the splitter is smaller than the difference between any of the standard gears, then it would create ratios between the standard gears as per Glen's (...) (18 years ago, 21-Dec-06, to lugnet.technic)
|
| | | | |
| | | | | | Re: What's the difference? —Steve Lane
|
| | | | (...) That makes a lot of sense. The configurations I was coming up with in my head, tended to duplicate ratio's I already had. Steve (18 years ago, 21-Dec-06, to lugnet.technic)
|
| | | | |
| | | | | | Re: What's the difference? —Benton Jackson
|
| | | | (...) Is it something like the front and rear sprockets of a 10+ speed bike? I know there are frequently duplications of gear ratios there. (18 years ago, 22-Dec-06, to lugnet.technic)
|
| | | | |
| | | | | | Re: What's the difference? —Steve Lane
|
| | | | (...) Yeah I suppose it would be, because you would have two different sets of gears that could both be changed. So in that way they'd be the same. The trick is to not duplicate ratio's because that's a waste. (18 years ago, 22-Dec-06, to lugnet.technic)
|
| | | | |
| | | | | | Re: What's the difference? —Glen Bell
|
| | | | (...) Yes, and keep in mind that the advantage with an 18speed transmission that I described in my last post,is that you could go through your low gears without splitting them, flick into high range and split whichever gears you want...gives you (...) (18 years ago, 23-Dec-06, to lugnet.technic)
|
| | | | |
| | | | | | Re: What's the difference? —Luis Hernández
|
| | | | (...) Mechanically, I would think of the splitter as an additional gearbox. Using the same example Maico gave, you have a 4-speed plus reverse gearbox. The splitter would be simply an additional 2-speed gearbox. Suppose the ratios in the 4-speed (...) (18 years ago, 8-Jan-07, to lugnet.technic, FTX)
|
| | | | |
| | | | | | Re: What's the difference? —Maico Arts
|
| | | | Hello All, Nice and correct description, Luis. A range changer would have a ratio of 1:4 in this example. (16z/16z and 32z/8z) A Splitter would have a ratio of 1: 1.25. (16z/16z and 16z/12z) Hmm, these ratios are a little bit hard to build though... (...) (18 years ago, 8-Jan-07, to lugnet.technic)
|
| | | | |
