 | | Re: How I've been procrastinating...
|
|
(...) Thanks! (...) That'll be rather difficult (tho not impossible) for I ripped it apart and put the 8475 back together--the 8466 was great for about 3-5 minutes, but it kills the batteries waaay too fast. (...) The motor is at one end, and a (...) (22 years ago, 1-Aug-02, to lugnet.org.ca.rtltoronto, lugnet.technic)
|
| |
| | Re: How I've been procrastinating...
|
|
(...) Very cool Dave! Nicely done. You should bring it to the next rtl dinner... ok, maybe with smaller tires for ease of transport ;) I can't figure out how you actually got the drive to the rear wheels. Is each of the new motors driving one of the (...) (22 years ago, 1-Aug-02, to lugnet.org.ca.rtltoronto, lugnet.technic)
|
| |
| | Znap-Snap Back to the drawing board
|
|
So there I am hang'n with my buddy Brian Sad, I was showing off my new Mecha Arm and the Znap Flex Axle snapped! Too bad, it was kind a cool set up. All we new was the arm was on the ground crawling around, and then the gears were just spinning. (...) (22 years ago, 1-Aug-02, to lugnet.technic)
|
| |
| | Re: New style diffs, driving rings and 16t clutch gears
|
|
(...) I've built a multi-function transmission/transfer-case for a Jeep. It includes a 4-speed transmission, which is then routed to a 2-speed transfer case. The 2-speed is exactly as ROSCO describes it. The output is then routed to the central (...) (22 years ago, 1-Aug-02, to lugnet.technic)
|
| |
| | Re: New style diffs, driving rings and 16t clutch gears
|
|
(...) I thought of a possible idea how you could use this as a means to make a car thats both a 2wd and a 4wd, where you select between them with a lever, much like on real 4wds. (22 years ago, 1-Aug-02, to lugnet.technic)
|
| |
| | Re: How I've been procrastinating...
|
|
(...) Added a few more pics of the 8466, scooting around the parking lot at work... (some action shots for y'all... ;) ) Dave K (22 years ago, 31-Jul-02, to lugnet.org.ca.rtltoronto, lugnet.technic)
|
| |
| | Re: New style diffs, driving rings and 16t clutch gears
|
|
"Ross Crawford" <rcrawford@csi.com> wrote in message news:H05y29.8wr@lugnet.com... (...) the (...) Has someone not made a locking diff with this? Jennifer (22 years ago, 1-Aug-02, to lugnet.technic)
|
| |
| | Re: Motors in parallel and stuff...
|
|
"Thomas Avery" <thomas.avery@intec-hou.com> wrote in message news:H057q6.Mrp@lugnet.com... extra motors? (...) into (...) I think the small 9V battery box is ok with one motor, but you can really see the difference with two or more motors under (...) (22 years ago, 1-Aug-02, to lugnet.technic)
|
| |
| | Re: New style diffs, driving rings and 16t clutch gears
|
|
(...) Well spotted! (...) Not that I know of... (...) The obvious one I can see is different gear ratio (using the 24t gear on the diff). Means you can get a really simple 2-speed trans without external gearing (like most of TLC's multi-speed (...) (22 years ago, 1-Aug-02, to lugnet.technic)
|
| |
| | New style diffs, driving rings and 16t clutch gears
|
|
Hi, Has anybody else noticed that the new style Technic differential housings (p/n 6573) have the same mouldings as the 16t clutch gears and could therefore be engaged by a driving ring. Has Lego ever used this feature in a set? Can anyone think of (...) (22 years ago, 1-Aug-02, to lugnet.technic)
|
