 | | Re: Turning the RCX off and on again (was: New pbForth 2.1.0 (and firmware speed))
|
|
(...) off (...) True. But I find not very practical to be forced to use the terminal to switch off the RCX or start the program again, expecially when you are attending a contest or take your robot to an exhibit. What I meant by "supervisor" is some (...) (22 years ago, 11-Apr-02, to lugnet.robotics.rcx.pbforth, lugnet.robotics.rcx)
|
| |
| | Two RCX with one IR-Tower
|
|
Hello, I want to control two RCX with one ir-tower. The problem is that the RCX should send back status information. Sending information to the RCX is quite easy: Both RCX receive the message but only one will perform the command. I found (...) (22 years ago, 11-Apr-02, to lugnet.robotics.rcx)
|
| |
| | Re: Turning the RCX off and on again (was: New pbForth 2.1.0 (and firmware speed))
|
|
(...) If you have the new version 2.1 the POWER-OFF word via terminal to shut off and the red button to power on works fine. If you have an earlier version (1.2x) you have to use the words RCX_INIT and POWER_INIT to initialize the brick and the (...) (22 years ago, 11-Apr-02, to lugnet.robotics.rcx.pbforth, lugnet.robotics.rcx)
|
| |
| | Turning the RCX off and on again (was: New pbForth 2.1.0 (and firmware speed))
|
|
Mario, i'm interested in pbForth example scripts, too. Furthermore, the "supervisor" you suggested could be the answer to one of my questions in (URL) concerning turning the RCX off and on without loosing pbForth: 2) According to Knudsen, i have to (...) (22 years ago, 11-Apr-02, to lugnet.robotics.rcx.pbforth, lugnet.robotics.rcx)
|
| |
| | Re: New pbForth 2.1.0 (and firmware speed)
|
|
Thanks Ralph, this is great news. I just got the new USB tower, and considering my revived interest for pbForth your new version arrives really at the right time. What IMHO would really boost the spreading of pbForth, is the availability of some (...) (22 years ago, 10-Apr-02, to lugnet.robotics.rcx.pbforth, lugnet.robotics.rcx)
|
| |
| | New pbForth 2.1.0 (and firmware speed)
|
|
For everyone that has been interested in firmware speed over the last few days, I am ready to announce the latest version of pbForth. This version supports the USB tower under Windows!!!! (URL) An empty loop of 20,000 interations takes less than 1 (...) (22 years ago, 10-Apr-02, to lugnet.robotics.rcx.pbforth, lugnet.robotics.rcx)
|
| |
| | RoboLab newsgroup page updates
|
|
The RoboLab newsgroup page (URL) some updating. The first two links on the left pane don't work anymore. The following two links should replace those first two links: Tufts RoboLab site (URL) or (URL) Education (Dacta) RoboLab site (URL) Pitsco site (...) (22 years ago, 10-Apr-02, to lugnet.admin.suggestions, lugnet.robotics.rcx.robolab, lugnet.dacta)
|
| |
| | RoboLab updates
|
|
If you only read the Robolab newsgroup then you may have missed a helpful post that did not appear in the RoboLab newsgroup. If so, then look at: "Robolab 2.5 patches" (URL) (22 years ago, 10-Apr-02, to lugnet.robotics.rcx.robolab)
|
| |
| | BricxCC release 3.3.4.5
|
|
I've released another version of BricxCC. This release fixes a couple minor bugs. The Code Explorer feature wasn't processing a file when it was first opened (it was waiting until the first change was made). That should work correctly in this (...) (22 years ago, 9-Apr-02, to lugnet.robotics.rcx.nqc)
|
| |
| | Re: Error Message
|
|
(...) I don't know if you are using BricxCC or not, but I get a single error when I try to compile this line of code if the target is set to Scout or Cybermaster. If I turn on the NQC 1.x compatibility mode via the Preferences dialog I get two (...) (22 years ago, 9-Apr-02, to lugnet.robotics.rcx.nqc)
|
